Hydraulic Model Studies?Pak Mun Hydroelectric Project (Thailand)
The paper presents briefly the hydraulic problems related to the project which were successfully solved by the 1 to 100 scale hydraulic model study carried out at the Asian Institute of...
Bed Forms of Nile River
In this paper, the observed bed forms for six different reaches of the Nile River in Egypt are described. The purpose of the study is to inquire whether or not the different available...
Sediment Transport Measurements in the Nile River at Bani Mazar
Measurements of sediment transport on the Nile River were conducted at Bani Mazar (200 km South of Cairo) during high and low water stages. Bed-load and suspended-load transport rates...
Movable-Bed Model to Evaluate Nile River Dredging
About 200 km south of Cario, at Bani Mazar reach, the Nile River has widened and formed several islands. The result is three channels with shallow depths. One of the branches must be improved...
Hydraulic Aspects of Grade Control Structures
This paper describes the function of grade control structures. The primary purpose of a grade control structure is to maintain or establish a desired bed elevation in a channel. Basically...
Bed Load Roughness in Supercritical Flow
A supercritical concrete channel is proposed for Mission Creek located in Santa Barbara County, California. The proposed channel may transport gravels and cobbles as bed load during large...
Operational Procedures for Estimating Bottom Exchange Rates
After briefly reviewing the terminology of the various bottom and water column exchange fluxes, the body of this paper summarizes five possible procedures for establishing operational...
Design of Groins on the Middle Rio Grande
The Albuquerque Projects Office of the Bureau of Reclamation wanted to use groins in place of revetments at two sites on the Rio Grande. The Bureau of Reclamation has limited experience...
Incipient Motion Criteria Defining Safe Zones for Salmon Spawning Habitat
Approximately 70% of the City of Seattle's water supply is drawn from the Cedar River. Between 200,000 and 400,000 sockeye salmon spawn annually in this partially dewatered...
A Study of Friction Factor for Flow in Gravel Bed Channels
For many years practicing engineers have faced the problem of predicting the resistance to flow in channels with rough surface. Flow in channel is a complex interaction between surface...
Calibration of Beni-Mazar Movable Bed Model
A sand-bed model representing a reach of the Nile River was constructed to study alternative solutions to maintaining the navigation channel. Flume tests were carried out first to determine...
Specification for the Design of Cold-Formed Stainless Steel Structural Members
ASCE's standard
Armor Layer Evolution
This communication presents an analysis of celerity propagation for non-uniform materials. Based on the corresponding flow, sediment transpot and sorting/armoring equations, the celerity...
Hydraulic Bridge Design for Movable Bed Conditions
This paper addresses the practical considerations of hydraulic design of a bridge under movable bed conditions. Hydraulic design tasks include pier and abutment scour calculations, design...
Model of Deposition of Grains from Debris Flow
Rapid deposition of grains from debris flow occurs in a channel whose slope angle decreases abruptly. A model of the deposition is presented on the basis of experiments and theoretical...
Scour in Non-Cohesive Beds at Culvert Outlets
An empirical relationship was developed to estimate the depth of scour in non-cohesive material at culvert outlets. The scour depth is expressed as a function of mean particle size of...
Bed Sediments and Bed Forms of the Lower Mississippi River
Approximately 500 bed material samples were collected from the thalweg of the Lower Mississippi River. At each sample location, a sonic record of the bed was obtained. From the appearance...
Sediment Concentration Measurements Below Small Headcuts
This study is designed to determine erosion rates downstream from a small headcut. The sediment concentration from a scour hole produced by a plunging jet is measured as a function of...
Variational Method in Fluvial Hydraulics?A Review
The theoretical base of the principle of minimum energy dissipation rate and other related stationarity hypotheses have been reviewed. Recent applications of the theory to the calculation...
Physical Modelling of Self Forming Alluvial Channels
A method is presented for the determination of a practicable physical model of self-forming channels in cohesionless alluvium. Both sand bed and gravel bed regime channels are considered....
Return to search