Dynamic Response Prediction for Earthquake Resistance Design of Bridge Structures
Newly developed nonlinear analysis procedures for assessing the earthquake resistance of bridges have been incorporated into the computer program SEISAB (SEISmic Analysis of Bridges)....
The Effect of Stiffness Degradation on the Three-Dimensional Seismic Response of Highway Bridges
This paper describes the effect of modeling of the inelastic pier behavior on the seismic response of three reinforced concrete bridges. Each bridge was analyzed twice once using a yield...
Experimental Evaluation of Performance of Earthquake Restrainers in Box Girder Bridges
Type C-1 restrainers were used in most of the concrete T- and box girder bridges which have been retrofit. Type C-1 restrainers consist of 7-3/4 in. diam. galvanized cables, bearing plates,...
Vertical Response Data from the Dominion Road Bridge Test
In January and February of 1985, two bridges were tested in New Zealand using simulated earthquake loads. The objective was to determine the in-situ seismic response of two reinforced...
Effects of Vertical Motion on the Inelastic Behavior of Highway Bridges
The response of typical highway bridges to the vertical component of earthquake ground motion has a significant effect on their elastic behavior. When vertical motions are considered along...
Consequences and Achievement of Supplemental Damping for Improved Seismic Performance
An earthquake resistant design philosophy which relies upon increased stiffness and damping rather than increased strength and ductility has been investigated. The effect of adding supplemental...
System Identification of Meloland Road Overcrossing
The Meloland Road Overcrossing (MRO) is a two-span reinforced concrete bridge structure located east of El Centro, California, 0.3 mi from the Imperial Fault. The Imperial Valley Earthquake...
System Identification of a Large Structure Using Pseudo-Dynamic Test Data
This paper deals with structural modeling and the determination of optimal nonlinear models by applying system identification techniques to inelastic pseudo-dynamic test data from a full-scale,...
Seismic Design of Highrise Building with Mega Frame
The NEC corporation head office building is under construction at Shiba Minato-ku, Tokyo, Japan. This building is a highrise building of steel structure with the height of 180m. The structural...
Structural Considerations in Design and Construction Process of a 25 Story Office Building
This paper introduces an example in which a steel office building of 25 stories above the ground was constructed employing innovative techniques. One of them was the use of precast concrete...
Seismic Design of a Long-span Space Structure
This structure consists of a 5 layered complex shape of long-span steel roof structure, and reinforced concrete (RC) and steel reinforced concrete (SRC) supporting structures. The roof...
Implications for Limit State Design of Inverted V Braced Steel Structures
Inverted V braced steel structures with backup ductile moment-resisting frames forming a dual system, exhibit complex inelastic behavior under severe seismic excitations. Thus, current...
Seismic Load Effects on a Scaled Model Structure
A long term observation on a scaled steel braced frame model with intentionally reduced seismic strength is ongoing since 1983. This paper examines the seismic load effects of two earthquakes...
Buckling Criteria for Earthquake-Induced Overturning Stresses in Cylindrical Liquid Storage Tanks
Perhaps one of the most common forms of seismic damage to cylindrical liquid storage tanks made out of steel is buckling of the tank wall due to vertical overturning stresses. Buckling...
Nonlinear Analysis for the Aseismic Strength of Highrise Steel Frame With Semi-Rigid Joints by Pseudo-Elastic Approach
This paper suggests that the direct stiffness method is still useful in dealing with the nonlinear analysis for the aseismic capacity of highrise steel frame while the Pseudo-elastic approach...
Effects of Semi-Rigid Connections and P-? Forces on the Optimum Design of Seismic Steel Frames
By utilizing methods of optimality critera and constraint gradients, the minimum weight design of semi-rigid planar steel frames subjected to static and seismic excitations is presented...
The Application of Seismic Isolation to Bridges
Unlike a building application the primary intent in a bridge is to protect the structure below the plane of isolation - the superstructure being relatively rigid to in-plane loads and...
The 1988 UBC Seismic Provisions for Steel Structures?An Overview
This paper will give the reader an introduction to the seismic design provisions for steel structures in the 1988 Uniform Building Code. Chapter 27 in the 1988 UBC now contains over ten...
1988 SEAOC and UBC Seismic Provisions
This paper highlights the major improvements to seismic design provisions incorporated in the 1988 Structural Engineers Association of California (SEAOC) 'Blue Book'...
Residual Capacity of Explosively Damaged Reinforced Concrete Columns
The results of load tests on explosively damaged reinforced concrete columns are presented. The method used to correlate an ultimate strength, laminar type of reinforced concrete analysis...
Return to search