Cold Regions Hydrology and Hydraulics
The Cold Regions Hydrology and Hydraulics Monograph is the eighth in a series of monographs prepared by the ASCE Technical Council on Cold Regions Engineering. The book is intended to...
Water Jets Fight Silt
In the largest U.S. application to date, an array of hydraulic jets is being used to scour a ship berth at the Port of Grays Harbor on the coast of Washington. The system has been in place...
The Truck Commodity Survey in the New York-New Jersey Metropolitan Area
The Truck Commodity Survey was designed to gather information on the characteristics of truck traffic at toll barriers with minimal disruption to traffic flows. It was developed by the...
Buckling Design of Vierendeel Reticular Shells
Double layer reticular shell structures carry very little transverse shear, thus, it may be appropriate to substitute the inter-layer diagonal members with 'space'...
Behavior of Cold-Formed Steel-Concrete Composite Beams
An experimental investigation was conducted at California State University - Long Beach to study the structural behavior of composite beams made of thin-walled cold-formed steel stiffened...
Stress Computations for Nearly Incompressible Materials
Computation of stresses by the finite element method (FEM) in the case of nearly incompressible isotropic elastic materials is discussed. It is shown that for moderately high Poisson's...
Flexural and Shear Moduli of FRP Beams
The analysis and design of structures of pultruded fiber reinforced plastic (FRP), constant cross-section, commercially produced, beams is discussed in the context of a shear deformation...
Ultimate Strength and Deformation of RC Panels
In this study, twenty reinforced concrete panels have been tested under pure shear. Test results showed that the compressive strength of concrete strut was strongly affected by bond characteristics...
Analytical Model for RC Panels Under Cyclic Load
There are several existing constitutive laws for cracked concrete and steel in RC developed in Okamura laboratory. These models have been developed and verified through reversed uniaxial...
Lateral Force Distribution in Manufactured Housing from Full-Scale Testing
The research focused on the behavior of two manufactured 14 ? 66 ft houses under simulated wind loads. Extensive instrumentation was employed to insure the collection of data that would...
Panel-Sheathed Shear Walls ? Past and Future
In order for a building to resist the lateral forces caused by wind or earthquake, it is necessary that the building include a lateral force resisting system. When the walls are designed...
Lessons Learned from Dynamic Tests of Shear Panels
Thirteen 8-ft by 8-ft shear panels and fifteen 16-in by 18-in shear panels were tested dynamically at the Structural Testing Laboratory, Richmond Field Station, University of California,...
A Structural Analysis Model for Timber Shear Walls
A numerical modelling procedure for the non-linear analysis of timber shear walls is presented. The model includes the non-linear behavior of the connectors between the sheathing and framing,...
Shear Strength of P.P.C. Beams
50 beams of partially prestressed concrete were tested and 82 data of the ultimate shear-strength were obtained. Based on these results, this paper studies the effects of the degree of...
Macroscopic Models for R/C Shear Walls
In this paper, the discussion is mainly focused on four macroscopic models, recently proposed by Japanese researchers, for predicting ultimate strength of reinforced concrete (R/C) shear...
Verification of Macroscopic Models for R/C Walls
Macroscopic models utilized in a plastic analysis for predicting the ultimate strength of reinforced concrete members have been developed in Japan as well as in Europe. In the JCI committee,...
Verification of Macroscopic Models or RC Walls by FEM
Several macroscopic models based on the limit analysis have been proposed for obtaining the ultimate strength of reinforced concrete shear walls in Japan. When using these models, it is...
Parametric Analyses of RC Shear Walls by FEM
In this paper, nonlinear behavior of reinforced concrete shear walls is studied by using the finite element analysis. We applied numerical analyses to a wide range of parameters, such...
Inelastic Performance of Single-Story Masonry Shear Walls
Twenty-two story-height reinforced masonry shear walls have been tested to examine the influence of the applied axial stress, and the amount of vertical and horizontal reinforcement on...
Nonlinear Finite Element Analysis of Experiments on Two-Story Reinforced Masonry Shear Walls
Nonlinear, static finite element analyses are being used for correlation with experiments conducted on one-story reinforced masonry shear walls, and for the prediction of and correlation...
Return to search