3D-Simulation of the Twin Lake Tracer Test
The 1983 Twin Lake tracer test was simulated using a three-dimensional finite element model. The model was calibrated comparing calculated and measured piezometric heads as well as vertical...
On the Calibration of Hydrologic Models
A procedure is proposed to calibrate hydrologic models to generate representative design flows and flood hydrographs. This procedure includes two calibration steps; event calibration and...
Global Search Technique to Calibrate Rainfall Runoff Models
The calibration of rainfall-runoff models in hydrology has not yet reached a satisfactory solution, using either manual or automatic procedures. This paper introduces a simple conceptual...
FLUME 3.0: A Computer Program for Designing Flumes and Weirs
Long-throated flumes and broad-crested weirs are becoming the preferred measuring devices for use in irrigation canals. A computer program for calibrating these flumes and weirs has been...
The ASCE Neutron Probe Calibration Study: Overview
A workshop was held at Logan, Utah to gather field information on neutron probe calibration and operation. Several techniques and instruments were compared. This paper serves to establish...
Soil Bulk Density Sampling for Neutron Gauge Calibration
The ASCE Task Committee on Neutron Gauge Calibration met in Logan, Utah in July 1992 to investigate the various methods of soil sampling, installation of access tubes, effect of various...
Measuring Soil Bulk Density Profiles with a Single Probe Gamma Density Gauge
Calibrating neutron depth gauges for measuring soil water content profiles requires soil bulk density data. In this study, the feasibility of using a single probe gamma density gauge to...
Error Analysis of Bulk Density Measurements for Neutron Moisture Gauge Calibration
Six bulk density sampling methods were evaluated for use in neutron gauge calibration. All six methods provided estimates of bulk density which were generally within 5% of bulk density...
Neutron Gauge Calibration Comparison of Methods
Several methods for obtaining soil samples for determining soil water content were used for field calibration of neutron gauges. This paper compares the results of calibration curves obtained...
Effect of Moisture and Bulk Density Sampling on Neutron Moisture Gauge Calibration
Three moisture and bulk density sampling methods were evaluated for use in neutron gauge calibration. Each of the methods was comprised of a single core or portions of a core taken during...
Development of San Gorgonio Pass Groundwater Flow Model I. Model Calibration
A groundwater flow model is being developed for use in management of a planned groundwater storage and recovery program for the Beaumont Storage Unit of the San Gorgonio Pass groundwater...
Calibration of Manning's Roughness for a River Reach
The Albuquerque Projects Office of the U.S. Bureau of Reclamation collected water surface elevations for measured discharges for the Rio Grande and many of its tributaries to try to obtain...
Use of Floodplain PCB Concentrations to Calibrate a River Hydraulics Model
A river floodplain was found to contain measurable quantities of polychlorinated biphenyls (PCBs), presumably deposited during historic flood events. A hydraulic model (HEC-2) was used...
Limitations of Reduced Scale Testing on Parshall Flumes
A model for the boundary layer development in the entrance section of a Parshall flume is developed to account for the effects of fluid viscosity on flume calibration equations. Data for...
The Concept of Local Euler Number as an Aid for Sizing Pitot Tubes
Correlations with drag coefficients enable determining the relations between the form of Pitot tubes and their velocity coefficients. A numerical example is presented to clear the use...
In-Flight Calibration of Mass Spectrometer
A new device for in-flight calibration of mass spectrometer is presented. At a ground station command the calibrator introduces a constant and reproducible amount of deuterium into the...
Calibration of Redundancy Factors for Highway Bridges
The object of this study is to develop a framework for considering redundancy in design and load capacity evaluation of highway bridge superstructures. The proposed method consists of...
Development of the San Fernando Basin Groundwater Flow Model
This paper describes the development and calibration of the San Fernando Basin (SFB) groundwater flow model. The SFB is the largest groundwater basin in the Upper Los Angeles River Area...
Calibration and Validation of the Storm Water Management Model to the Providence Area Combined Sewer System
This paper exemplifies the calibration and validation of the EPA Storm Water Management Model (SWMM) to one drainage area within the Providence (RI) area combined sewer overflow system....
Modeling Stormwater Basin Effects
This paper presents results of an extension to a study included earlier in these proceedings on the downstream accumulation effects of stormwater detention basins. The previously calibrated...
Return to search