Stiffness Requirements for HDPE, Profile Wall Pipe
For the past two years the Gulf Oil Corporation has sponsored a research study on profile wall High Density Polyethylene (HDPE) pipe at Texas A & M University. A pipe design computer...
The Relative Strain as a Design Criterion for Buried uPVC Gravity Sewer Pipes
When designing buried plastic sewer pipes, the relative strain caused by deflection of the circular pipe section is of particular interest. The reason for increased interest is the present...
Strains Induced by Combined Loading in Buried Pressurized Fiberglass Pipe
In 1983 Owens Corning Fiberglas and Utah State University collaborated on a study of combined strain behavior of fiberglass pipe to quantify the bending strain reduction as a function...
Stress and Strain Responses of a Soil-Pipe System to Vehicular Traffic
A 16-in. natural gas pipeline near Racine, Wisconsin, had been in service for some 30 years. In 1982 road widening operations on a line parallel with the pipe presented the opportunity...
Field Testing of 84-Inch-Diameter Plastic Pipe
During the summer of 1981, a research project was initiated to monitor strains and deformation in 84-inch diameter RPM (reinforced plastic mortar) pressure pipe. Three 20-foot (6. 1-m)...
Design of Non-Pressure Very Flexible Plastic Pipe
There is considerable debate about the correct structural design procedure to be used for very flexible plastic pipe (VFP) - typically glass-fiber reinforced pipe (GRP), reinforced plastic...
Girth Weld Defect Tolerance Criteria
This paper describes the following criteria proposed for setting allowable defect sizes in girth welds: PD 6493:1980, 'Guidance on Some Methods for the Derivation of Acceptance...
Time-Dependent Damage and Creep of Brittle Rock
In this paper, some results of a combined analytical-experimental study of the relationship between subcritical microcrack growth due to stress corrosion and the time-dependent deformation...
Continuum Modeling of Discrete Structures with Geometric Nonlinearities
The modeling of geometrically non-linear discrete structures by an equivalent continuum is presented. The discrete-continuum analogy is developed by first isolating a unit cell of the...
Small Strain Measurements Using Triaxial Apparatus
This paper presents a detailed testing methodology which can be used to determine the cyclic properties of soils at very small strains using triaxial apparatus. A discussion of specific...
A Study of Deformations in Concrete Faced Rockfill Dams
This paper presents the results of studies on the behavior of certain concrete faced rockfill dams (CFRD), which were conducted during the Basic Design of Machadinho dam in Brazil. The...
Tension Tests of Containment Wall Isolated Liner Plates
Two tests were conducted using an approximate 2:1 ratio of hoop to meridional load. This simple load ratio is a gross approximation of the liner plate loading in a containment subjected...
Structural Performance Predictions for Liner Plates on Nuclear Facilities
The history of the use of liner plates is presented. It is shown that the liner plate can be buckled, and can be bonded or not bonded to the concrete. The buckled plate usually has bending...
Design Criteria for Buried Flexible Pipe
A modified CANDE program was used to analyze a full factorial set of design parameters for buried, large diameter high density polyethylene profile-wall pipe. A new pipe subroutine was...
Easing Strains in Partner-Managed Firms
The family-like nature of partnerships promotes shared management responsibilities but creates conflict. Partnerships, like families, are often taken for granted by the partners. Nonpartners...
The Simple-Pile Approach to Pile Installation in Clays
This article describes the fundamentals of the approach and presents solutions for the effects of quasi-static deep undrained penetration of a simple solid pile on the deformations and...
The Theory of One-Dimensional Consolidation of Saturated Clays
The theory of nonlinear finite strain consolidation is reviewed. A modification of the effective stress equation to account of settling and consolidation as a unified phenomenon is proposed....
The Use of Soil Mechanics Capabilities in a General Purpose Finite Element Program
This paper describes capabilities, points out features of implementation in a general purpose code, and describes some numerical considerations. The paper makes use of illustrative solutions....
Application of Finite Strain Consolidation Theory for Engineering Design and Environmental Planning of Mine Tailings Impoundments
A knowledge of the consolidation behavior of mine tailings, during and after deposition, is important in estimating final impoundment capacity, rate and pore fluid expulsion during and...
Measurement of Ice Forces on Structures
Methodologies and techniques are discussed for measuring ice forces on fixed structures situated in rivers and lakes. The usual method of measuring ice forces is to place a load frame...
Return to search