Cut and Cover Construction of the SSC Injector Tunnels
The injector system of the Superconducting Super Collider (SSC) constitutes the string of tunnels where protons are accelerated to near the speed of light and injected into the main collider...
The Challenge of Housing the Largest Detector
The most innovative part of the structural-civil design of the Superconducting Super Collider (SSC) is that of the underground experimental halls located alongside the 86 kilometer collider...
High Strength Shotcrete and Concrete on the SSC Project
This paper addresses the technical aspects related to the use of high strength shotcrete and concrete on the Superconducting Super Collider (SSC) project. 7,000 psi shotcrete and 8,000...
SDC Detector Foundation Requirements for the SSC
The Solenoidal Detector Collaboration (SDC) detector weighs approximately 32,000 metric tons, and its ability to perform to design specifications is directly related to its internal alignment....
An Overview of Shotcrete Usage on the SSC
Shotcrete has been widely used on the Superconducting Super Collider for initial support of tunnel excavations in both the strong and weak rock formations encountered. Different types...
Dynamic Testing of Unreinforced Brick Masonry Infills
A significant seismic hazard may exist when unreinforced masonry infill panels fall out of their surrounding frames as a result of excessive accelerations applied normal to their plane....
Limit States Analysis of Masonry Arches
The limit states analysis of masonry arches, heretofore used only for the analysis of hinging mechanisms within the arch ring, is shown to have wider applicability. Lower and upper bounds...
A Peice-wise Linear Evaluation of Masonry Infills Subjected to Out-of-plane Seiesmic Drift
This paper summarizes the out-of-plane testing and analytical modeling of a full-scale unreinforced masonry (URM) infilled frame and a bare frame without infilling. The testing was part...
Seismic Strengthening of URM Buildings with Steel Bracing
Unreinforced masonry (URM) buildings with large open fronts are extremely vulnerable to seismic inputs posing serious life safety hazard. Steel bracing systems have been used to upgrade...
Shear Design Guidelines for Polyester Concrete Using Recycled Plastic
Previous research on the shear behavior of steel-reinforced polymer concrete (PC) beams has been very limited and no efficient design procedures have been proposed. In all the previous...
Load Carrying Capacity of SPC Composite Column
This paper reports the result of beam column test of a new type composite columns. High-strength precast-concrete panels (hereafter denoted as PCa-panels) are fixed to the steel square...
Dynamic Response of Steel Fiber Reinforced Concrete
Extensive research has been done on the static properties of steel fiber reinforced concrete, but very little on the dynamic properties. A total of 20 beams was tested. The steel fiber...
Damping Systems for Controlling Wind Induced Motions of Structures
This paper presents the state-of-the-art in damping systems for controlling wind induced motion of structures and their applications in the U.S. and Japan. Both passive and active systems...
Characterization of an ER Active Member
In the presence of strong electric fields (kV/mm), electrorheological (ER) materials change form viscous fluids to yielding materials. The class of ER materials used in this study have...
Wind Deflection Probability Analysis
A statistical analysis is performed which analyses the probability of various magnitudes of deflections of a cable-stayed roof occurring due to wind uplift. Extensive wind analyses were...
Advances in the Modelling of Long Span Bridges for Wind Effects
The continued development of longer span suspension and cable-stayed bridges has placed increased demand on both the designers and constructors of these structures for a better understanding...
Synthetic Wind for Investigations in Time-Domain
Buffeting investigations of large bridges carried out in time-domain permit modelling of the non-linearity of the system and wind force. Correct simulation of the natural wind plays a...
Reliability of Light-Gage Metal Joist Hangers
Limit state design equations are formulated to assess the reliability of light-gage metal joist hangers using the results of experimental studies. The design equations are calibrated against...
Fracture Analysis of Bolted Timber Connections
Application of fracture mechanics concepts to splice connections where bolts load timber members perpendicular to the grain is discussed. Attention is given to prediction of the load level...
Proposed Test Method for Determining Bending Yield Moment of Nails
Current engineering design procedures use a yield theory to establish the nominal resistance (capacity) for laterally-loaded nailed connections in engineered structures. In order to develop...
Return to search