Some Examples of Latticed Structures in Spain
Since the middle of the last sixties latticed structures have extensively been used in Spain to cover different large areas as factories, churches, marketplaces, exhibition palaces etc....

Elastic Stability of Non-Prismatic Columns
A matrix analysis technique for determining the elastic buckling loads for columns of general form is presented along with several numerical examples. In this technique, a non-prismatic...

Analysis of Tapered and Stepped Columns by Analogy to Cantilever Deflection
An analysis is developed for handling the buckling design of tapered and stepped columns with the aid of the so called 'amplification factors'. When these factors...

Optimum Design of Tapered Tubular Members
An algorithm for designing a tubular structural member with constant taper is presented. The design criterion is that the maximum absolute stress produced by a set of loading conditions...

Buckling Load of Tapered Columns
The basic tapered column with larger section in the center, is considered using Rayleigh-Timoshenko method. Column has linearly increasing Io with...

Buckling of Variable Cross-Section Columns
An approximate solution for the problem of buckling of variable cross-section columns, loaded by variable axial force is given, for several boundary conditions. Both the cross-section...

Parametric Study of Bracing in Lattice Towers
The behaviour of cross-bracing comprising struts and ties connected at their cross-over joints in lattice towers is subject to some uncertainty. It is affected significantly by taper and...

Design Issues in Steel Buildings
The Committee on Design of Steel Building Structures of the Committee on Metals of the Structural Division of ASCE was formed in 1981, with the express purpose of studying problems that...

Steel Girt Design
Procedures are presented for the design of light gage cold formed girts and hot rolled girts. The effects of continuity, sag rods, and wall sheeting are discussed. Design procedures are...

Floor Vibrations ? Tips for Designers
The purpose of this paper is to suggest a number of practical concepts which can be used to improve the performance of floor systems subject to occupant induced motion from either walking,...

Composite Floor Vibrations: Predicted and Measured
Several steel composite floor systems of relatively long span trusses for a number of high rise structures in the Chicago area have been subjected to field measurements to evaluate their...

Buckling of Unsymmetrical Thin-Walled Members
The formulation of a three-dimensional model based on p-version finite element method for the elastic buckling analysis of unsymmetrical thin-walled members under axial compression and...

Behavior of Cold-Formed Steel-Concrete Composite Beams
An experimental investigation was conducted at California State University - Long Beach to study the structural behavior of composite beams made of thin-walled cold-formed steel stiffened...

Cold-Formed Z-Sections Under Axial Load and Bending
The use of cold-formed Z-section members as beam-columns presents some unique design problems which are not adequately addressed in the current design specifications. If these members...

Automated Load Capacity Determination of Cold-Formed Steel Compression Members
This paper presents an automated approach for the evaluation of the axial load capacity of nine cold-formed steel sections according to the latest AISI-1986 Cold-Formed Steel Specification....

Structures with Semi-Rigid Bolted Connections
Modern methods of aseismic protection encourage use of connections capable to dissipate energy with little or no deformations. The present paper is a summary of studies of semi-rigid bolted...

Seismic Response of Flexibly-Connected Steel Frames
The response of typical low-rise steel building frames designed by the 'Type 2 Construction' method to moderate earthquakes is examined. Such frames are often...

Tests on Brace and Link Connections for EBFs
This paper describes recent test results on the behavior of selected connections for seismic-resistant Eccentrically Braced Frames (EBFs). These tests provided data on the performance...

Brace Connections for Ductility
Influence of connection design on the seismic behavior of welded bracing members made of double channels is studied in this paper. Shortcomings of commonly used connection details as per...

End Plate Moment Connections for Cyclic Loads
Three pilot tests of full size end plate moment connections under cyclic loading are discussed. In one of the specimens, the premature fracture of one of the inner bolts suggests the possibility...

 

 

 

 

Return to search