Elastic Stability of Non-Prismatic Columns
A matrix analysis technique for determining the elastic buckling loads for columns of general form is presented along with several numerical examples. In this technique, a non-prismatic...
Optimum Design of Tapered Tubular Members
An algorithm for designing a tubular structural member with constant taper is presented. The design criterion is that the maximum absolute stress produced by a set of loading conditions...
Buckling of Variable Cross-Section Columns
An approximate solution for the problem of buckling of variable cross-section columns, loaded by variable axial force is given, for several boundary conditions. Both the cross-section...
Parametric Study of Bracing in Lattice Towers
The behaviour of cross-bracing comprising struts and ties connected at their cross-over joints in lattice towers is subject to some uncertainty. It is affected significantly by taper and...
Buckling of Unsymmetrical Thin-Walled Members
The formulation of a three-dimensional model based on p-version finite element method for the elastic buckling analysis of unsymmetrical thin-walled members under axial compression and...
Structures with Semi-Rigid Bolted Connections
Modern methods of aseismic protection encourage use of connections capable to dissipate energy with little or no deformations. The present paper is a summary of studies of semi-rigid bolted...
Seismic Response of Flexibly-Connected Steel Frames
The response of typical low-rise steel building frames designed by the 'Type 2 Construction' method to moderate earthquakes is examined. Such frames are often...
Tests on Brace and Link Connections for EBFs
This paper describes recent test results on the behavior of selected connections for seismic-resistant Eccentrically Braced Frames (EBFs). These tests provided data on the performance...
Brace Connections for Ductility
Influence of connection design on the seismic behavior of welded bracing members made of double channels is studied in this paper. Shortcomings of commonly used connection details as per...
Strength of Biaxially Crooked Jumbo Columns
The ultimate strength of axially loaded jumbo columns with biaxial initial out-of-straightnesses is analyzed by the finite element method. The analysis makes use of the measured residual...
Behavior of Single Angles Under Compression and Biaxial Bending
Angle struts are being used extensively as web members of trusses, bracings of buildings, and they are widely used as main members in transmission and lattice towers. Because of their...
Stablity Considerations in the New E&CS Building
The new Engineering and Computer Science (E & CS) building at California State University, Sacramento (CSUS) is a five-story structure characterized by two shear walls in the east-west...
Stability Analysis of Steel Compression Members by a Modified Finite Strip Method
The method of structural stability analysis utilized in this paper is a combination of the classical bending theory and the finite strip method. Combining the assumptions of traditional...
Hysteresis Studies Including Post Buckling of Angle Web-Members for Truss-Type Girders
The paper presents analytical studies of the buckling capacities and hysteresis behavior of angle-web members of truss-type girders. The eccentricity between the loading point and the...
Stability Analysis in Bracing and Support Design
A post-buckling stability analysis is carried out for struts with multiple elastic lateral supports. Both hinged-end and fixed-end conditions are considered. A criterion of sufficient...
Lateral Buckling of Beams: General Considerations
The paper presents a solution for the elastic, lateral-torsional buckling of beams under unequal end moments using Worthington's method of superposition of modes involving...
Portal Frame Stability with Nonproportional Loads
An inelastic theoretical study of the effect of various load paths is conducted on the in-plane behavior of an imperfect portal frame with flexible joints. The loading consists of concentrated...
Optimal Shape Design of Columns for Buckling
A procedure for the shape optimization of a column for prescribed buckling load is developed. The procedure uses a new analysis technique that enables the formulation of the optimization...
Optimized Wall Thickness of Shells of Revolution
The aim of this paper was to develop a concept for the design of shells of revolution with different Gaussian curvature using a simplified finite element buckling analysis. A cooling tower...
Original Formulation of the Finite Element Method
Following a brief summary of the 1952 state of the art of structural analysis, the paper describes the circumstances that led to the formulation of the finite element method by members...
Return to search