High Molecular Weight Methacrylate for Sealing Cracked Concrete
The sealing of cracks in concrete surfaces has been one of the most difficult types of repair to accomplish. Epoxy injection has been widely used, but due to its relatively high cost,...
Sprayed-On Polymer Mortar Construction
Sprayed-on polymer mortar has been used to construct low-cost, lightweight structures in a variety of locations. The addition of the two-component additive to one cubic yard of mortar...
Concrete Strength-Quality Assurance
The usual criterion for establishing grades of structural concrete is the compressive strength measured in an arbitrary manner on a standardized specimen stored in a stipulated fashion...
Early Age Strength Detection for In-situ Concrete
In recent years it has become increasingly beneficial to know the quality of concrete as soon as possible after it has been placed. This is especially true for high-rise concrete buildings...
Lessons Learned in Laboratory and Field Evaluation of Accelerated Strength Tests for Quality Control of Concrete Pavements
This paper describes the results of an accelerated strength testing program performed to evaluate flexural strength potential at 28- and 90-days. Based upon a literature review of previous...
Flexural and Shear Moduli of FRP Beams
The analysis and design of structures of pultruded fiber reinforced plastic (FRP), constant cross-section, commercially produced, beams is discussed in the context of a shear deformation...
Development of High Strength Composite Cables
Fiber reinforced composite materials offer significant advantages over conventional materials, for such factors as corrosion resistance, lighter weight, and higher strengths. These advantages...
Compressive Deterioration of Cracked Concrete
When shear behavior of reinforced concrete (R/C) members is to be simulated, the compressive strength and the stiffness reduction of cracked concrete must be taken into consideration....
Ultimate Strength and Deformation of RC Panels
In this study, twenty reinforced concrete panels have been tested under pure shear. Test results showed that the compressive strength of concrete strut was strongly affected by bond characteristics...
Shear Strength of P.P.C. Beams
50 beams of partially prestressed concrete were tested and 82 data of the ultimate shear-strength were obtained. Based on these results, this paper studies the effects of the degree of...
Macroscopic Models for R/C Shear Walls
In this paper, the discussion is mainly focused on four macroscopic models, recently proposed by Japanese researchers, for predicting ultimate strength of reinforced concrete (R/C) shear...
Verification of Macroscopic Models for R/C Walls
Macroscopic models utilized in a plastic analysis for predicting the ultimate strength of reinforced concrete members have been developed in Japan as well as in Europe. In the JCI committee,...
Parametric Analyses of RC Shear Walls by FEM
In this paper, nonlinear behavior of reinforced concrete shear walls is studied by using the finite element analysis. We applied numerical analyses to a wide range of parameters, such...
Strength Evaluation of Existing Reinforced Concrete Structures
The load test as described in ACI 318-83 Chapter 20, entitled 'Strength Evaluation of Existing Structures,' was conducted at 60%, 80%, and 100% of the calculated...
Flexural Strength of Ultra-High Strength Concrete Members
Various proposals have been made for the pridiction of strength of high strength concrete sections. One of the most important parts of any strength computation procedure is the assumption...
Member Design Equations for a LRFD Wood Specification
A key step in the preparation of a load and resistance factor design (LRFD) based design specification for engineered wood construction is the selection of the behavioral equations for...
Inelastic Performance of Single-Story Masonry Shear Walls
Twenty-two story-height reinforced masonry shear walls have been tested to examine the influence of the applied axial stress, and the amount of vertical and horizontal reinforcement on...
Use of Experimental Data to Develop Probable Behavior
The intent of this paper is to present results of research that studies the performance of the University of Colorado walls tested by Professor Benson Shing. These walls would be classified...
Ductility and Failure Characteristics of Concrete and Rock Subjected to Complex Load Paths
Strength, ductility and the complex material response features of concrete and rock should be evaluated through carefully planned material properties test programs designed to subject...
A Damage Model for Reinforced Concrete
The damage index developed by the authors models concrete damage as a low-cycle fatigue phenomenon. By quantifying the energy dissipated as a fraction of the total energy dissipation capacity,...
Return to search