Geotechnical Aspects of Stiff and Hard Clays
This publication contains articles that deal with field and laboratory measurements of engineering properties of stiff (overconsolidated) clays, and comparisons of predicted and measured...
Pressuremeter and Foundation Design
The design of shallow and deep foundations on the basis of pressuremeter results is analyzed using numerous load tests and case histories. The foundations are shallow footings subjected...
Field Permeability Test for Earthen Liners
A sealed double-ring infiltrometer (SDRI) was developed for in-situ measurements of the hydraulic conductivity of earthen liners and covers. The characteristic of the SDRI that distinguishes...
In-Situ Testing of Peat
It is often economical therefore to start geotechnical investigations with a study of maps and serial photographs and to continue with a detailed program of field reconnaissance. Standard...
Reliability of Pile Capacity Assessment by CPT in Overconsolidated Clay
Correlations for unit skin friction and end bearing are established between cone penetration test (CPT) records, triaxial data and a small data base of measured skin friction and end bearing...
Use of SPT and CPT Tests for Evaluating the Liquefaction Resistance of Sands
A cone penetration test (CPT)-liquefaction resistance relationship has been established using the large body of standard penetration test (SPT) data. Factors for relating CPT tip resistance...
Predictions of Pile Shaft Capacity With the PLS Cell
In situ measurements of stresses and pore pressures on a model pile shaft, the Piezo-Lateral Stress (PLS) cell, are utilized to reconstruct the conditions of load tests involving two large...
Probabilistic Study of SPT Liquefaction Analysis
The influence of earthquake magnitude upon the commonly used correlation between Standard Penetration Test (SPT) blow count and liquefaction potential is evaluated using a probabilistic...
Laboratory and Field Evaluation of Cone Penetrometers
Cone penetrometers from 8 organizations have been studied by performing laboratory tests and field tests. The testing show that pore pressure and temperature zero shift affect significantly...
The DMT - ?hc Method for Piles Driven in Clay
This paper presents a tentative method for evaluating the limiting skin friction f//s for piles driven in clay based on sigma //h'c (horizontal effective stress at the interface...
Determining Sand Strength by Cone Penetrometer
Evaluation has been made of several theories and methods for deducing sand strength from cone resistance. Bearing capacity theories, cavity expansion theory, and empirical methods have...
Measurement of Vertical Ground Vibrations
This paper examines the use of surface and embedded mountings, to which transducers are attached for the measurement of free field vertical ground vibrations. Upper limits to the frequency...
Soil Improvement Evaluation by CPT for Tanks
Trial soil improvement by gravel compaction piles and dynamic consolidation, and a subsequent full-scale loading test on loose volcanic ash soil were conducted prior to the design of large...
High Quality Sampling and In Situ Testing for Deep Water Geotechnical Site Investigation
This paper discusses methods that have been used to conduct geotechnical investigations in water depths up to 2500 feet. Investigations can be conducted from supply boats, geotechnical...
Effect of Cementation on the Cone Penetration Resistance of Sand
A laboratory study was conducted to investigate the effect of cementation on the cone penetration resistance of sand. A new apparatus to form homogeneous artificially cemented sand specimens...
Design Parameters for Grouted Piles in Rock From In-Situ Load Tests
A series of pile load tests were performed at an onshore site to develop final geotechnical parameters for the Gaviota platform foundation which consists of large diameter drilled and...
Bearing Capacity of Footings on Clay CPT Method
A method is proposed to predict the ultimate bearing pressure for footings on clay using data from cone penetration tests. This method relates the ratio of ultimate soil bearing for a...
Skin Friction Evaluated From Friction Meter Test
This paper first describes the features of a specially developed friction meter and its operation method, and then reports in-situ test results conducted on various types of soils at two...
Uplist Capacity of Pile Foundations Using CPT Data
Southern California Edison Company has performed field uplift load tests on concrete driven piles, cast-in-place straight shaft piles and cast-in-place belled piers along transmission...
Effctive Stress Interpretation of In-situ Tests
Significant differences in terms of load-settlement curves obtained from Plate Load Tests (PLT) and q//c profiles obtained from Static Cone Penetration Tests (SCPT) at two sites with different...
Return to search