FRP Box-Beams Under Long-Time Static and Fatigue Loading
This paper discusses experimental and analytical aspects of the long-time behavior of filament wound E-glass fiber reinforced epoxy-box-beams. Theoretical and experimental data are compared...
Design of Lateral Steel in Columns
Lateral steel in columns is generally required for shear resistance, confinement of concrete and prevention of buckling of longitudinal bars. This paper is limited to the design of lateral...
Rational Limits for Longitudinal Steel in Concrete Columns
Current limits for the amount of longitudinal reinforcement in concrete columns were established more than 60 years ago. Commercial grades of reinforcement in 1930 were about half as strong...
Proposed Hurricane Wind Speeds for ASCE 7-95
A 2-3 second peak gust wind map has been proposed for the wind load provisions of ASCE 7-95, now in draft form. On the hurricane coast, speeds from published Monte Carlo analyses were...
Load and Resistance Factors for Bridge Design Code
The paper summarizes the code development procedures used for the new LRFD (load and resistance factor design) bridge code. The current specifications use allowable stresses and/or load...
LRFD Provisions for Wood Bridges
A project to develop a load and resistance factor design (LRFD) edition of the American Association of State Highway and Transportation Officials (AASHTO) Standard Specifications for Highway...
Unified Code Provisions for Concrete Bridges
Provisions on limiting the flexural reinforcement adopted in the new AASHTO LRFD Specification for Bridge Design are summarized (1). They address minimum and maximum levels of reinforcement...
The Use of Coda Waves for Characterizing the Site Effect on Strong Ground Motion
The well established separability of source, path and site effects on coda waves of local seismic events offers the most effective means for determining the site amplification factor empirically....
Seismic Behavior of Type PR Steel Frames
Type PR(partially restrained 'simple framing') is one of the methods of design specified in the AISC LRFD(1986) Design code for the design of unbraced steel building frames. In this method...
Mechanical Behavior of Dowels Embedded in Concrete
In this paper an experimental investigation on the behavior of dowels embedded in concrete is described. The dowel strength under monotonic forces with two different boundary conditions...
Probabilistic Evaluation of Human Perception Threshold of Horizontal Vibration of Buildings (0.125Hz to 6.0Hz)
Vibration perception tests are conducted both for low frequencies of high-rise buildings and high frequencies of low-rise residential buildings. The vibration frequency is varied from...
A Self-Balancing Laminate
A self balancing wood laminate has been developed based on the principle of orthotropic elasticity. Lumber is cut into three sections in the flatwise plane and each side member is turned...
Fracture Analysis of Bolted Timber Connections
Application of fracture mechanics concepts to splice connections where bolts load timber members perpendicular to the grain is discussed. Attention is given to prediction of the load level...
Proposed Test Method for Determining Bending Yield Moment of Nails
Current engineering design procedures use a yield theory to establish the nominal resistance (capacity) for laterally-loaded nailed connections in engineered structures. In order to develop...
Consequential Fire Loads on Structures
Much less consideration has been given to the performance of modern structural and architectural systems during fires and to the minimization of damage that threatens the integrity of...
Wind Loads on Low Rise Structures: A Survey
Because of the large investment, high rise buildings are usually tested in a wind tunnel to provide the best wind loading information possible. Since low rise structures each represent...
Uplift Resistance of Plywood and OSB Roof Sheathing
A test program to determine the resistance of plywood and OSB roof sheathing to uplift pressures created by wind flowing over a residential roof structure will provide valuable data to...
NDE for Steel Bridges: FHWA Research, Past, Present and Future
Over the last two decades the Federal Highway Administration (FHWA) has sponsored numerous research and development projects in the area of nondestructive evaluation of steel bridges....
AISI-FHWA Model Bridge Test
The Model Bridge Study involved a large experimental test program to evaluate the behavior of a 0.4-scale model of a two-span continuous plate-girder bridge with modular precast prestressed...
Horizontally Curved Steel Bridge Research-Update 2
Theory and data necessary for the development and calibration of an LRFD based curved steel bridge specification do not presently exist. To address these needs, the Federal Highway Administration...
Return to search