Sediment Routing and Stream Bed Evolution Model
A one-dimensional numerical model developed by Borah, Alonso and Prasad is discussed, improved and tested. The model named STREAM routes graded sediments and simulates aggradation, degradation...
Riverine 2D Random Walk Transport Model
A random walk transport model was developed to avoid the amplitude and phase errors inherent in finite difference models. A three-point probability distribution was used for the random...
Hydraulic Investigation of the Cache River Basin
To develop a comprehensive solution to the problems that exist in the basin, the Illinois State Water Survey has initiated a hydraulic study. This ongoing research includes collection...
Ackers-White Equation: Transportation by Size Fractions
The Ackers-White procedure for sediment transport has been modified to permit calculation by size fractions. The original logic has been retained, but A values for incipient motion have...
Roughness Coefficients of Large Floods
Most hydraulic calculations of flow in channels and overbank areas require an evaluation of flow resistance generally expressed as Manning's roughness coefficient, n. Literature...
An Overview of Factors Affecting Land Application of Food Processing Wastes
The food processing industry can use slow rate, rapid infiltration or overland flow systems. Slow rate systems are the most common method used for land application. The limiting design...
Winery Wastewater Land Application
Winery wastewater is characterized by low pH, relatively high BOD, and a low nutrient content. Land application using rapid infiltration basins has been practiced successfully at a number...
CWSI and Stomatal Resistance of Cotton and Soybeans
A new instrument, Scheduler(TRADEMARK), has been developed to measure the onset and duration of plant water stress. This device consists of a sensor package (containing an infrared thermometer,...
Redundancy Evaluation of Existing Bridges
The redundancy of an existing bridge can only be correctly assessed by considering the full superstructure as a single entity. Any formulation based on the analysis of bridge components...
Calibration of a Bridge Rating Formula for Overload Permits
This paper proposes a method to calibrate a reliability based load and resistance factor design (LRFD) permit evaluation formulation that will account for the overloaded truck's...
LFRD Bridge Design as Viewed by the Designer
The load and resistance factor design (LFRD) design concept has been resisted by some bridge engineers on the grounds that it represents a reduction of the 'factor of safety'...
Multiple Presence Reduction Factors for Bridges
This paper reviews the multiple presence reduction factors specified in the AASHTO and Ontario codes, and provides a method by which these factors can be established in relation to volume...
Overview of the Guidelines for T/L Structure Loadings
This section introduces a reliability based design methodology that forms the framework for the loading guidelines. A Load and Resistance Factor Design (LRFD) format is presented for the...
Steel Plate Girder Alternate I-10/I-17 Interchange
The scope of the Phoenix I-10 Viaduct allowed extensive study for the optimization of this moderate span steel plate girder bridge. The value engineering studies lead to the use of the...
Prediction of Deformations Due to Heat Curving
This paper summarizes the state of the art in the thermal deformation techniques. Alternate analytical methods are described. The limitations and accuracy of these models are noted, and...
Wind Buffeting of Cable-Stayed Bridges During Construction
Some of the dominant loadings on a cable-stayed bridge during construction are a result of the non-uniform vertical and horizontal gust forces on the deck and the associated dynamic response...
Design of Bridge Piers Against Ship Collision
Design rules for unprotected bridge piers, using uniform safety requirements, are proposed. The selection of an appropriate design vessel is based on a risk assessment model which uses...
Evaluation and Surveillance of Concrete Bridge Structures
A number of cost-effective techniques are available for evaluation and surveillance of concrete bridge structures. The methods covered in this paper include: long-term bridge instrumentation,...
The Behavior of R/C Pinned Bridge Columns under Lateral Loading
Four one-eighth scale one-way hinge details of the type used in highway bridges were tested to study the effect of combined shear and flexure caused by lateral loads. The aspect ratio...
Wind Tunnel Investigation of a Twin Deck Suspension Bridge
Wind tunnel measurements of the response of a twin deck suspension bridge to dynamic wind loads are presented. The investigation was concerned with the determination of the deck response...
Return to search