Calibration of a Bridge Rating Formula for Overload Permits
This paper proposes a method to calibrate a reliability based load and resistance factor design (LRFD) permit evaluation formulation that will account for the overloaded truck's...
LFRD Bridge Design as Viewed by the Designer
The load and resistance factor design (LFRD) design concept has been resisted by some bridge engineers on the grounds that it represents a reduction of the 'factor of safety'...
Multiple Presence Reduction Factors for Bridges
This paper reviews the multiple presence reduction factors specified in the AASHTO and Ontario codes, and provides a method by which these factors can be established in relation to volume...
Overview of the Guidelines for T/L Structure Loadings
This section introduces a reliability based design methodology that forms the framework for the loading guidelines. A Load and Resistance Factor Design (LRFD) format is presented for the...
Steel Plate Girder Alternate I-10/I-17 Interchange
The scope of the Phoenix I-10 Viaduct allowed extensive study for the optimization of this moderate span steel plate girder bridge. The value engineering studies lead to the use of the...
Prediction of Deformations Due to Heat Curving
This paper summarizes the state of the art in the thermal deformation techniques. Alternate analytical methods are described. The limitations and accuracy of these models are noted, and...
Wind Buffeting of Cable-Stayed Bridges During Construction
Some of the dominant loadings on a cable-stayed bridge during construction are a result of the non-uniform vertical and horizontal gust forces on the deck and the associated dynamic response...
Design of Bridge Piers Against Ship Collision
Design rules for unprotected bridge piers, using uniform safety requirements, are proposed. The selection of an appropriate design vessel is based on a risk assessment model which uses...
Evaluation and Surveillance of Concrete Bridge Structures
A number of cost-effective techniques are available for evaluation and surveillance of concrete bridge structures. The methods covered in this paper include: long-term bridge instrumentation,...
The Behavior of R/C Pinned Bridge Columns under Lateral Loading
Four one-eighth scale one-way hinge details of the type used in highway bridges were tested to study the effect of combined shear and flexure caused by lateral loads. The aspect ratio...
Wind Tunnel Investigation of a Twin Deck Suspension Bridge
Wind tunnel measurements of the response of a twin deck suspension bridge to dynamic wind loads are presented. The investigation was concerned with the determination of the deck response...
Analysis and Design of Wind- and Earthquake-Resistance of an S-Curved Cable-Stayed Bridge
Just recently, in January of 1987, the first S-curved cable-stayed bridge in the world has been completed as a part of Metropolitan Expressway's Katsushika-Edogawa Route in...
Safety of Long Span Highway Bridges Based on Dynamic Response
This paper consists of an analytical study regarding the dynamic response of highway bridges subjected to heavy vehicle loads, with emphasis on long span low fundamental frequency bridges....
A Comparative Study of Different Base Isolators
A comparative study of the effectiveness of four different base isolators is carried out. The structure is modeled as a rigid mass and the accelerograms of the North-South component of...
Seismic Response of Simple Structures with Coulomb Damping
A single story structure incorporating a floor-sliding mechanism for dissipation of vibration energy through Coulomb friction damping is examined. The response of this structure is evaluated...
Cracking of a Tilt-Up Structure Due to Dynamic Loads
The extensive cracking of a tilt-up reinforced concrete structure is discussed. The site investigation revealed horizontal cracks at two feet to seven feet above a mezzanine level which...
Nonlinear Axisymmetric Uplift of Circular Plates
A formulation of a method of analysis of the nonlinear axisymmetric response of the bottom plate of a liquid storage tank under uplifting forces is presented. At first, the plate is assumed...
Methods for Improving the Seismic Response of Concentrically Braced Steel Frames
This paper briefly reviews various factors contributing to the poor performance occasionally observed in concentrically braced steel frame structures during recent earthquakes. Several...
Unusual Shaped Highrise Buildings in Seismic Zone
The structural concepts, seismic analysis and design of five recent highrise structures are presented in this paper. The paper deals with the problem of multistory buildings having 'structural...
The Design and Construction of the Washington State Convention and Trade Center Over Interstate 5
The Washington State Convention and Trade Center is a 10-level, 1,000,000-square foot facility constructed over Interstate 5 in downtown Seattle. The project spans over three city streets...
Return to search