A Damage Model for Reinforced Concrete
The damage index developed by the authors models concrete damage as a low-cycle fatigue phenomenon. By quantifying the energy dissipated as a fraction of the total energy dissipation capacity,...
Amelioration of Stirrup and Compression Reinforcement on the Ductility of Reinforced High-Strength Concrete Beam
18 rectangular high strength concrete beams were tested to investigate their ductile behavior. The results show that it will be more advantageous, for ductility, to choose the compressive...
Seismic Strengthening of a Historic Unreinforced Masonry Building
The building involved is a four-story unreinforced masonry structure. Considerations related to development of design criteria are presented along with retrofitting strategies. The building...
Seismic Strengthening of a Tall Masonry Building
The design of a strengthening system for a tall building is proposed using ductile reinforced masonry shear walls. This innovative design concept produced a system that controlled the...
1988 SEAOC and UBC Seismic Provisions
This paper highlights the major improvements to seismic design provisions incorporated in the 1988 Structural Engineers Association of California (SEAOC) 'Blue Book'...
Tension Leg Platform
a State of the Art Review
Prepared by the Task Group on Compliant Offshore Platforms of ASCE. This report considers the analysis and design of tension leg platforms (TLPs),...
Collapsible Soils in the Antelope Valley�California
Soils subject to hydroconsolidation, commonly referred to as collapsible soils, have a potential to undergo significant volume reductions upon wetting, with or without additional loading...
Fracturing of Rock Using Expansive Soundless Chemical Demolition Agents
The theoretical principles of the action of expansive soundless chemical demolition agents are presented. The procedure for using these demolition agents are briefly outlined. Differences...
Bearing Pressure?SPT Correlations for Expanded Base Piles in Sand
Design of enlarged base piles is usually carried out using correlations between SPT N values and point resistance. The results of full scale load tests are used to show that base resistance...
Performance of a Large Ribbed Mat on Cohesive Soil
The performance of a 678-ft by 304-ft (207-m by 93-m) ribbed concrete mat was studied to provide improved soil input parameters for design. The mat was constructed on a low plasticity...
Bearing Capacity of Shallow Foundation on Granular Column in Weak Clay
Laboratory model tests results for the ultimate bearing capacity of shallow rectangular foundations supported by granular columns made in weak clay have been presented. In all cases, the...
Chemically Induced Foundation Heave
The Kerr-McGee Electrolysis Plant in Henderson, Nevada has had recorded upward movements of portions of the building in excess of 18 inches. Contours of the measured heave indicate that...
Ponds and Lagoons of Gulf Islands National Seashore
A physical and natural resource survey was conducted of the ponds and lagoons on Horn and Petit Bois Islands, Gulf Islands National Seashore, Mississippi. Petit Bois Island contains 17...
Dredge Disposal Monitoring by Fourier Shape Analysis
Fourier grain-shape analysis characterizes a population of sediments in terms of the shapes of the grains. The technique of grain-shape analysis has been successfully applied to the area...
Geocosta Operations?A Program of Oceanographic Expeditions for the Brazilian Inner Shelf
In July 1979, a new expedition was conducted with the R.V. Almirate Camara, in the same area as GEOMAR X, with the following purposes: surveying profiles with side scan sonar and conducting...
Structural Design, Analysis and Testing
This volume contains the papers presented in 21 sessions of the 1989 Structures Congress held in San Francisco. The papers cover a wide range of topics including types of construction...
Structural Materials
This volume of Structural Materials contains papers from 12 sessions of the 7th Structures Congress held in San Francisco on May 1-5, 1989. The sessions cover a very broad range of topics...
Design of Plastic Piece Parts
This paper describes a computer assisted design process originally developed at the University of Wyoming and now implemented in commercial software. In order to address the need for broadly...
Stereolithography
Stereolithography is a three-dimensional printing process which produces accurate copies of CAD solid or surface models directly from CAD data. The process uses a moving laser beam, directed...
Gamma Exposure from Rn Progeny in GAC Units
An investigation into the gamma exposure rate generated by granular activated carbon (GAC) water treatment units focused on ten sites that covered a range of source radon (Rn) in water...
Return to search