A Knowledge-Based System for the Environmental Design of Waterways (ENDOW)
Knowledge-based software systems accept problem descriptions from users and apply logic in order to generate a solution or solution set. These systems function over very narrow problem...
LISP or CLIPS: Selecting an Expert System Tool in Hydraulic Engineering
The transfer of Artificial Intelligence(AI) technology from the research laboratories to the scientific and engineering environments has been made possible by phenomenal advances in computer...
A Dynamic Runoff Model for Disturbed Hillslopes
A dynamic runoff model is developed for use in analyzing the hydrologic response of disturbed hillslopes. The model employs an explicit form of the Green-Ampt equation which is coupled...
On The Application of Artificial Viscosity in Computational Hydraulics
Artificial viscosity is a particular kind of truncation error that is either implicity present or explicitly added to the finite difference schemes. It is shown that the method of lines...
Probabilistic Aspects of Hydroproject Maintenance
A survey of operation and maintenance personnel in the hydraulic structures sector was conducted to learn about the present maintenance approach and the perception of the probabilistic...
Conventional Storm Drainage Which Recharges the Groundwater
Since the demand for water is on the rise, more resourceful means of retaining and controlling the release of stormwater is needed. This retained stormwater may then be used for aesthetic...
Verification of WASURO Using the Puerto Nuevo Physical Model Study Results
The Jacksonville District, US Army Corps of Engineers, used the hydraulic design computer modeling program, WASURO, for preliminary design of the Rio Puerto Nuevo Flood Control System....
Detention Basin Design to Control Flood Volumes
A desk-top method is presented for hydraulic design of detention basins. The main objective is to control the flood volume rather than the peak discharge. The method is based on the pre-determined...
Hydraulic Roughness and Sediment Yield in Wheel Ruts on Forest Roads
Clear water flow and sediment yield from simulated wheel ruts in a forest road were measured at five different sites in the Northern Rocky Mountains. These measurements provided information...
Model Studies on Local Scour
In this investigation, the scaling procedure of a scour model in the laboratory has been indicated. The results have been compared with the prototype data....
Effect of Manning's Roughness Coefficient in Simulating Flow Parameters in Natural Channels
Manning's roughness coefficients are presented for three of the oldest and largest irrigation canals in Egypt. The discharges ranges from 35 to 318 m3/s....
Cofferdam Rip-Rap Protection for the New Esna Barrage
A 1:60 undistorted mobile bed model of the Nile River in the vicinity of Esna Barrage was constructed at the Hydraulics and Sediment Research Institute to test rip-rap protection of the...
Calibration of Beni-Mazar Movable Bed Model
A sand-bed model representing a reach of the Nile River was constructed to study alternative solutions to maintaining the navigation channel. Flume tests were carried out first to determine...
Fluvial Recharge of Sand Mining Pit
Accuracy in modeling fluvial processes becomes increasingly important as development occurs along waterways. The FLUVIAL-12 (1, 2) model is used to simulate the recharge of sand mining...
Safety Analysis of Handset Wood Slab Formworks
A reliability index is calculated for flexural strength of a handset wood slab formwork system. Load and resistance models are based on a survey of construction loads and wood test data...
Limit States Design of Wooden Formwork for Concrete Walls
Load and resistance factors are developed for ultimate limit states design of wooden formwork components for concrete walls when the lateral concrete pressures are computed using the ACI...
Development of Standards for Slipform & Jumpform Works
Review of past work indicates substantial effort has been made to publish construction standards and guidelines for slipforms but published material pertaining to jumpforms is scarce....
Designing Plans for Constructability
The writer has obtained several years experience acting as construction engineer for roadway rehabilitation projects as a consulting engineer. In this capacity, it is necessary to provide...
Kinematics and Trajectory Planning for Robotic Excavation
One of the high volume and repetitive construction operations at the construction site is the excavation of soil. Automation of the excavation work requires a robotic system that is able...
Air-Water Transfer: The Role of Partitioning
A review is presented of the role of air-water equilibrium in determining the direction and rate of transfer of chemicals between water bodies and the atmosphere. Because this diffusive...
Return to search