Optimal Design of Tall RC Tube Buildings
The analysis and design of reinforced concrete framed tube buildings is formulated as a nonlinear optimization problem and solved using modern design optimization software. The influence...
Optimization of Structures Subjected to Vibrations
A minimum cost optimization procedure is presented for the analysis of multi-degree freedom structures subjected to steady, transient and random vibration environment. The procedure is...
Production of Masonry Blocks for Developing Countries
The need for nuturing of low cost building materials industry in developing countries has long been recognized throughout the world. costs of building materials. Therefore, construction...
Seismic Resistant Low-Cost Masonry Buildings in Peru
Future housing in developing countries will be provided mainly in medium rise, four to six stories, bearing wall masonry buildings. This paper reports on the rationality behind this political...
Sprayed-On Polymer Mortar Construction
Sprayed-on polymer mortar has been used to construct low-cost, lightweight structures in a variety of locations. The addition of the two-component additive to one cubic yard of mortar...
Wood Diaphragms: Performance Requirements and Analytical Modeling
Wood diaphragms represent the principal mechanisms for resisting lateral loads in many light-frame buildings. While recent research has provided several mathematical models for predicting...
LRFD for U. S. Bridge Design ? Validation Issues
During the 1987 meeting of the AASHTO Subcommittee on Bridges and Structures, recommendations from the National Cooperative Highway Research Program (NCHRP), Project 20-7/31, regarding...
Energy Approach of Earthquake-Structural Design Analysis
A new procedure developed from the earthquake energy concepts is presented in this paper. A short-squat building and a long-slender building are analyzed using the presented procedure....
Mitigation of Wind-Induced Vibration of Tall Buildings
This paper summarizes a detailed study of the sensitivity of building acceleration to changes in structural stiffness, mass and damping and to the eccentricities in the centers of stiffness...
Aerodynamic Methods for Mitigating Wind-Induced Building Motions
Excessive wind-induced motions of tall buildings most frequently result from vortex shedding induced across-wind oscillations. This form of excitation is most pronounced for relatively...
Dynamic Response of a Building with Dual System
The paper presents the dynamic response of a 30-story building with dual system consisting of cross-bracing and beam-column moment resisting frames. Two types of beam-column connections,...
Analysis and the Design of Multi-Layer Viscoelastic (V.E.) Dampers for Tall Structures
Vibrational motion of tall buildings can be damped by employment of viscoelastic passive dampers in the structure. The type of dampers selected depend on locations where relative displacements,...
Local Wind Pressures on Roofs
The paper reviews the results of the most recent research studies in the evaluation of wind pressure coefficients for the design of roof cladding elements. The effect of roof geometry...
Ballasted Single Ply Design Guide Development
A new roofing concept called ballasted single ply has now captured about 25% of the new and retrofit flat roof market. This concept relies on the use of ballast to provide the wind resistance...
Load Combinations for LRFD With Wood Construction
Probability based limit states design for wood construction is complicated by the fact that wood is a natural material with large variations in mechanical properties and is sensitive to...
Heath Building?Load Paths of an Underpinning
A case study of an underpinning is presented which, in principle, consists of the introduction of a transfer system in an existing building. The transfer system modifies the load paths...
Codified Reliability for Structures During Construction
It is generally acknowledged that the most critical stage of a structure's lifetime is that of construction, leading to failures or locking in forces and deformations that...
Standards for Design Loads During Construction: An ASCE Effort
ASCE embarked on a new standards activity by the Design Loads for Structures During Construction Standards Committee. The objective of the effort is the development of standard guidelines...
Remote Automatic Data Acquisition Systems
Personal computers have been used on two projects to monitor peformance of structures in an automatically triggered mode. In both cases a local PC is used to continually monitor a triggering...
Pressure Measuring System for Wind Loads
A project to acquire wind and building surface pressure data in the field is continuing at Texas Tech University. A test building of dimensions 30 ? 45 ? 13 ft (9.1 ? 13.7 ? 4.0 m) and...
Return to search