Offshore Dredging - Is it still Cost Effective for Beach Restoration?
Offshore dredging has been the source of sand for beach restoration in southeast Florida since Broward County constructed the first project in Pompano Beach in 1970. However, with increasing...
Dredging Developments in the Canadian Arctic
The use of dredges in the Canadian Arctic in connection with oil exploration programmes has lead to the adaptation of existing and adoption of new techniques. Further development is required...
Design and Construction - Theodore Ship Channel
Environmental impacts, greater technological capabilities, and improved evaluation techniques make the disposal of large quantities of dredge material more complex and involved. Also,...
Open Water Disposal for Marsh Creation James River, VA
There is a need for close cooperation between design and construction of levees on soft foundation for containing dredge material. The scope of this study included marine exploration,...
Turbidity Generated by a Model Cutterhead Dredge
The study of turbidity generation indicates that, in general, turbidity increases with an increase in the cutter speed and an increase in the cutter swing velocity. A silt curtain deployed...
Dredge Automation: The State-of-the-Art
Automated control systems are being developed and applied to enhance the productivity and cost-effectiveness of dredges. Referring particularly to hydraulic type dredging plants, the functions...
Abrasion Resistance of Polyethylene Dredge Pipe
In recent years there has been a slow but steady increase in the number of dredges using high density polyethylene (HDPE) pipe in discharge lines. HDPE's increased popularity...
Development of the Dredging Wheel
The 'bucket line' dredge and 'cutter suction' dredge are two distinct types of equipment. The cutter suction system has developed more...
Selecting a Dredge Pump
While it is not necessary for the dredge operator to know how to design a dredge pump, the ability to select one that meets his project requirements is essential to insure the success...
Dredge Cutterhead Flow Processes
Feasibility studies of new dredge intake and cutterhead shielding techniques were conducted to improve hydraulic cutterhead dredge performance. Simple modification of the suction mouth...
Dredging-Related Considerations in Navigation Channel Design
In the design of a navigation project, the channel depth, width, and alignment for a given set of navigation requirements are dependent on physical, hydrodynamic, and sedimentological...
Influence of Roughness on Velocity and Dispersion at Low Flow
Dependence of the hydraulic and transport characteristics of low flow on channel roughness is investigated. Empirical expressions are used to estimate roughness coefficient as a function...
Effects of Fines in Gravel Bed Streams Behavior
A model-gravel bed stream is studied in the laboratory. Flow visualization of bedload motion correlates with bursting phenomena near the bed. The bedload variation as a result of the addition...
Numerical Model of Mississippi River at Lock and Dam 26
Replacement work was initiated in November 1979. The first stage cofferdam constricted about half of the river channel. As a result, the flow velocity at the constriction increased causing...
Hydraulic Uncertainty in Risk Analysis
Considerable effort has been expended in defining and evaluating hydrologic uncertainties; however, the analysis and evaluation of hydraulic uncertainties has received little attention....
Dynamic Reliability Models for Hydraulic Structures
In addition to the determination of capacity and layout of hydraulic structures under normal design, one other important but related task that faces engineers is the evaluation of reliability....
Reliability Analysis as Reflected from the Fourth International Symposium on Stochastic Hydraulics
Reliability analysis is perhaps one of the most practically important branches of the general field of stochastic hydraulics. Its potential applications include quantitative evaluation...
RCC Dam Incorporates Innovative Hydraulic Features
An overview of the features of Monksville Dam is presented, with emphasis on the hydraulic components of the project. This 150-foot (45-meter) high roller compacted concrete structure...
Upper Hudson River Valley Dam Break Model
In order to determine areas of inundation due to the failure of Conklingville Dam, a dam break analysis was performed, and the resulting outflow hydrograph was routed through the downstream...
Mechanics of Mudflows
A Bingham model is adopted to study the fluid mechanics of mudflows. Equations for predicting the transition from laminar to turbulent flow in an open channel are formulated and verified...
Return to search