Three-Dimensional Finite Element Analysis of Stress and Activation in the Heart
A finite element (FE) method has been developed for three-dimensional (3D) analysis of stress distributions and activation patterns in the left and right ventricles of the canine heart....
Biomechanical Model of a Lumbar Intervertebral Joint?A System Approach
This study was conducted to determine the forces sustained by the lumbar ligaments under flexion-compression using a two-dimensional equilibrium model. The lumbar motion segment was modeled...
Normal and Tangential Contact of Layered Spheres as Models of Joint Contact
The causes of cracking in degenerating cartilage are examined using analytical models of layered elastic spheres in normal and tangential contact. Vertical surface and deep radial cracks...
A Contact Problem Modeling the Squeeze-Film Mode of Synovial Joint Lubrication
A contact problem modeling synovial joint lubrication under squeeze-film conditions is studied. In this model, the thin synovial fluid layer is incompressible and linearly viscous, and...
Buckling Loads of Columns Made of Viscoelastic Materials
This is about the developing of relationships for predicting the change of buckling loads of columns made of viscoelastic materials under different loads. When a columnlike structural...
Buckling of Lamianted Plates Using h-p Finite Strips
The paper presents a computationally efficient alternative to the finite element method for the initial buckling analysis of long, shear-deformable composite laminates. In addition the...
A Mixture Finite Element for Reinforced Concrete
A semi-analytical finite element is presented for analyses of cracked reinforced concrete (RC) structures including bond action between rebar and concrete, and crack-face shear transfer....
Interlaminar Fracture Toughness Test: Traditional and Modified
For brittle, transversely isotropic, composite materials we have developed an alternative Mode II interlaminar fracture toughness test (GIIc) that...
A Damping Model for the Vibration of Nonlinear Laminated Composite Cylindrical Panels with High Order Transverse Shears
The damping characteristics of nonlinear vibration of a cylindrical panel including large displacements/rotations and parabolic transverse shears has been discussed in this study. The...
On the Adhesive Strength of Viscoelastic Fibrous Composites
A methodology for solving problems of anisotropic materials using the theory of elasticity (viscoelasticity) is presented. Some results on specific problems related to the stressed-and-deformed...
Statistical Strength Analysis of Composites
A new modified six parameter Weibull distribution model has been adopted to analyze strength data structure of ARALL laminated and graphite-epoxy composites. This model shows better correlations...
Partial Hybrid Stress Element for Higher-Order Laminated Plates Theory
The partial hybrid stress method is applied to higher-order plate theory for orthotropic laminated plates. This new element performs better than displacement formulation and approaches...
Flexural and Extensional Motion of Moderately Thick Laminated Composite Plates
A general theory of flexural and extensional motion of moderately thick laminated composite plates is developed for linear elastic materials and small deformation. Interlaminar stresses...
Failure Characterization of Structural FRP Bars
A combined experimental and theoretical investigation on the structural behavior of fiber reinforced plastic (FRP) bars is presented. Test results indicate that the ultimate strength decreases...
Bond Strength of Reinforcing Bars in SIFCON
This paper presents a brief summary of an ongoing investigation on the bond characteristics of deformed reinforcing bars embedded in a SIFCON matrix. A significant increase in bond strength,...
Mixture Considerations for High Performance Cement-Based Composites
In the present paper, mixture considerations for producing high performance cement-based composites are discussed. Effects of different factors such as grain size and fiber reinforcement...
Studies of the Interfacial Properties of Fiber Reinforced Cement
The multiple fiber pull-out tests were conducted with steel wires and alkali resistant glass fiber strand in order to characterize the behavior of interface of fiber and cementitious matrix....
Material Testing at High Pressure
A static test cell has been designed and fabricated to apply a peak stress of up to 2 GPa to a 2.54 cm cylindrical specimen. The cell design was based on the 'belt'...
Strain Rate Effects on Pressuremeter Testing
This paper discusses the effect of strain rate on the cavity expansion problem and pressuremeter test. A cuboidal shear device, CSD, was used to perform pressuremeter strain path tests...
Instability and Plastic Flow of Soils
Materials should according to Drucker's postulate become unstable when the second increment of plastic work is negative. Experimental observations however show otherwise....
Return to search