Owner and Designer Advantages Derived from Use of Construction Consultant
There are two significant ways that an experienced construction consultant can assist both the owner and the designer/engineer in obtaining an economical and practical structure. Constructibility...
Some Observations on Undrained Side Resistance of Drilled Shafts
A data base of 106 field load tests (65 in uplift and 41 in compression) is used to evaluate the undrained side resistance of drilled shaft foundations. The total stress or alpha (?) method...
Pile-Drilled Caisson Combination for Foundation of High Rise Building
The analysis and evaluation of several alternatives for foundations of a high rise office building is presented, which resulted in the selection of a combination of high capacity piles...
Combination Drilled Shaft and Driven Pile Foundation for a High-Rise Building
A case history is presented which discusses the design and construction of a combination drilled shaft and driven pile foundation which supports a high-rise in San Francisco. Drilled piers,...
Performance of a Building Foundation Designed to Accommodate Large Settlements
The Eastern Airlines shuttle terminal at LaGuardia Airport in New York City is supported on spread footings founded in an incinerated refuse fill which overlies a deep deposit of slightly...
Complex High-Rise Foundation Design and Construction
The substructure design and construction of a 60 story office tower in downtown Chicago is described. The presence of existing belled caissons on hardpan required use of filtered dewatering...
A New Combined Footing and Drilled Shaft Foundation Design
A conventional belled caisson foundation installation in glacial till to support a suburban Chicago 10-story office building was stopped when test caissons revealed excessive water-bearing...
Interaction of Geology, Construction Practice and Foundation Design
The influence of geologic knowledge and construction practices on the geotechnical foundation design process has been assessed and summarized. Particular emphasis has been given to the...
Integration of Research Into Design Practice
A widely held perception is that research results flow from the research community along the paths of professional publication into the design offices, where they find practical application....
Innovative Foundation Designs for Permafrost Conditions in the Arctic
This paper describes the engineering solution to restore the structural properties of permafrost at a site location in the Western Operating Area of the Prudhoe Bay Field. Steel pile supports...
The CADD Landfill
Designing landfills with CADD, engineers have reduced cut and fill calculations from two weeks to two days. Aerial surveys arrive on magnetic tapes and are loaded into computers by in-house...
Countering Terrorist Threats
Musacchio & Rozen assessed the risks and vulnerabilities to a possible terrorist attack of the data processing center of a large European bank. With the increasing use by terrorist...
Facilities Management With CADD
Tyson led a project that began in 1985 to develop an integrated alphanumeric and graphic database for facilities management at Stanford University. Many large institutions could benefit...
Automating Design of Boston's Artery
Boston's Central Artery project is being designed with in-house programs that are helping to overcome problems caused by the sheer volume of diversified data being handled...
Selected Papers from Chinese Journals of Structural Engineering
This book is an initial effort to introduce selected papers from journals published by the China Civil Engineering Society to ASCE membership. The twenty papers in this volume were selected...
Sulfide in Wastewater Collection and Treatment Systems
ASCE Manual 69, Manual of Practice on Sulfide in Wastewater Collection and Treatment Systems, is intended to help planners, designers, and operators of wastewater facilities understand...
Seismic Engineering
Research and Practice
This volume of Seismic Engineering: Research and Practice contains papers from twenty-two sessions of the 1989 ASCE Structures Congress. These papers represent a wide-ranging interest...
Steel Structures
The seventy-eight papers included in this volume cover the fifteen sessions generally associated with steel structures presented at the Seventh Annual Structures Congress held on May 1-5,...
University-Industry Cooperation for Effective Education and Research in CAD/CAM
It is well known that, for successful conception, manufacture, and marketing of a new product, design and manufacturing activities must be closely coordinated. Decisions made at the design...
Freshman Programming and Engineering Design: Comedy, or Tragedy
It is apparent from the literature, as well as discussions with faculty at other colleges of engineering, that the topics of freshman engineering design and computation are being dealt...
Return to search