Tension Leg Platform
a State of the Art Review
Prepared by the Task Group on Compliant Offshore Platforms of ASCE. This report considers the analysis and design of tension leg platforms (TLPs),...
An Evaluation of Pile Design in Fraser River Delta Using In-Situ Tests
Modern methods of pile design often take advantage of in-situ test data. Thirteen axial pile capacity design methods have been evaluated using the results from eight full-scale pile load...
Collapsible Soils in the Antelope Valley�California
Soils subject to hydroconsolidation, commonly referred to as collapsible soils, have a potential to undergo significant volume reductions upon wetting, with or without additional loading...
Fracturing of Rock Using Expansive Soundless Chemical Demolition Agents
The theoretical principles of the action of expansive soundless chemical demolition agents are presented. The procedure for using these demolition agents are briefly outlined. Differences...
Analysis of Pile Load Tests at Lock and Dam 26
This is a summary of the results collected during the extensive load test program performed by the U.S. Army Engineer District, St. Louis, during the construction of the new Lock and Dam...
Bearing Pressure?SPT Correlations for Expanded Base Piles in Sand
Design of enlarged base piles is usually carried out using correlations between SPT N values and point resistance. The results of full scale load tests are used to show that base resistance...
Performance of a Large Ribbed Mat on Cohesive Soil
The performance of a 678-ft by 304-ft (207-m by 93-m) ribbed concrete mat was studied to provide improved soil input parameters for design. The mat was constructed on a low plasticity...
Bearing Capacity of Shallow Foundation on Granular Column in Weak Clay
Laboratory model tests results for the ultimate bearing capacity of shallow rectangular foundations supported by granular columns made in weak clay have been presented. In all cases, the...
Interpretation of Instrumented Driven Steel Pipe Piles
This paper presents the results of a series of studies on the behavior of driven close-ended steel pipe piles. Extensive field explorations and geotechnical analyses have been carried...
Cost Effective Pile Foundation Supports Fast Track Paper Mill
This paper decribes the generalized subsurface conditions, pile evaluation and load test program, pile and piling contractor selection, production pile installation, and quality assurance...
Chemically Induced Foundation Heave
The Kerr-McGee Electrolysis Plant in Henderson, Nevada has had recorded upward movements of portions of the building in excess of 18 inches. Contours of the measured heave indicate that...
Innovative Foundation Designs for Permafrost Conditions in the Arctic
This paper describes the engineering solution to restore the structural properties of permafrost at a site location in the Western Operating Area of the Prudhoe Bay Field. Steel pile supports...
Ponds and Lagoons of Gulf Islands National Seashore
A physical and natural resource survey was conducted of the ponds and lagoons on Horn and Petit Bois Islands, Gulf Islands National Seashore, Mississippi. Petit Bois Island contains 17...
Dredge Disposal Monitoring by Fourier Shape Analysis
Fourier grain-shape analysis characterizes a population of sediments in terms of the shapes of the grains. The technique of grain-shape analysis has been successfully applied to the area...
Geocosta Operations?A Program of Oceanographic Expeditions for the Brazilian Inner Shelf
In July 1979, a new expedition was conducted with the R.V. Almirate Camara, in the same area as GEOMAR X, with the following purposes: surveying profiles with side scan sonar and conducting...
Structural Design, Analysis and Testing
This volume contains the papers presented in 21 sessions of the 1989 Structures Congress held in San Francisco. The papers cover a wide range of topics including types of construction...
Structural Materials
This volume of Structural Materials contains papers from 12 sessions of the 7th Structures Congress held in San Francisco on May 1-5, 1989. The sessions cover a very broad range of topics...
Design of Plastic Piece Parts
This paper describes a computer assisted design process originally developed at the University of Wyoming and now implemented in commercial software. In order to address the need for broadly...
Stereolithography
Stereolithography is a three-dimensional printing process which produces accurate copies of CAD solid or surface models directly from CAD data. The process uses a moving laser beam, directed...
Gamma Exposure from Rn Progeny in GAC Units
An investigation into the gamma exposure rate generated by granular activated carbon (GAC) water treatment units focused on ten sites that covered a range of source radon (Rn) in water...
Return to search