The Response of Steel Containment Models to Internal Pressurization
To obtain insight and data on the response of containment vessels subjected to beyond design basis accidents, four 1/32 scale steel containment models have been subjected to internal overpressurization,...
Major Considerations in Scale Modeling of Reinforced Concrete Containment Structures
Reinforced concrete containment structures pose unique modeling problems, especially when leakage integrity is of interest. This paper presents a general discussion of modeling considerations...
Containment Integrity of SEP Plants under Combined Loads
The containment designs analyzed consisted of three inverted light-bulb shaped drywells used in boiling water reactor (BWR) systems, and three steel-lines concrete containments and a spherical...
Determination of Containment Vessel Ultimate Capacity Using Nonlinear Finite Element Analysis
Analysis of steel containment vessels is normally performed using linear elastic solutions with allowable stresses specified by applicable design codes. This method gives little indication...
Onsite Storage Facility for Low Level Radwaste
The Tennessee Valley Authority (TVA) has designed and constructed an onsite storage facility for low level radwaste (LLRW) at its Browns Ferry Nuclear Plant in northern Alabama. The paper...
Safety Investigations of Existing Spent Fuel Storage Structures for Increased Spent Fuel Storage Capacity
Delays in the solution of disposal problems continue to create the need for additional on-site spent fuel storage capacity at commercial nuclear power generating facilities. Rod consolidation...
ACI 349 Embedments: Code Provisions and Methods of Analysis
Steel embedments form the critical link between steel and concrete structures. Appendix B of ACT 349, Code Requirements for Nuclear Safety Related Concrete Structures, specifies the ultimate...
State-of-the-Art Report on Steel Embedments
The basic philosophy underlying the design of steel embedments may be summarized as follows: (1) If an attachment can be located such that a group of cast-in-place anchors can be used...
As-Built Locations Through Precision Photography
This paper describes a new application of close range photogrammetry as a technique for obtaining reliable as-built locations of embedded threaded inserts in concrete structures and the...
Design of Thin Wall Reinforced Concrete Pipe Using Dimension Ratio (DR)
Dimension Ratio is defined as the ratio of the internal pipe diameter to the pipe wall thickness. The Caltrans culvert research leading to the development and use of the Dimension Ratio...
Importance of Pipe Soil Stiffness Ratio in Plastic Pipe Design
In this paper, the finite element method of analysis is used to study the effect of pipe-soil stiffness ratio on axial forces, bending moments, and deflection of pipes of varying stiffness....
The Present Status of Application of the Plastic Concepts in Structural Design
The different approaches of recognizing plastic behavior in the design of steel structures are reviewed and the design requirements that assure successful utilization of this behavior...
Computer-Automated Limit-States-Design of Steel Frameworks
The paper concerns the computer-automated synthesis of minimum-weight planar steel frameworks. For any number of applied loading cases, the design of the structure may be constrained by...
Limit State Analysis of Lattice Steel Transmission Towers
The background and present status for limit state analysis of lattice steel towers at the Bonneville Power Administration is presented. Conceptual development, a computer program, and...
Reliability-Based LRFD for Transmission Structures
A simple reliability-based Load and Resistance Factor Design (LRFD) method is proposed for the structural design of electric transmission lines. With the proposed method, the designer...
Pile Caps Subjected to Lateral Loads
This paper reviews current pile cap design practices and presents results of tests on two pile caps with different reinforcement locations. Lateral load tests performed on two pile cap...
Role of a Standard in the Production of Drilled Shafts
The preparation of drawings and documents that describe the details of the installation of drilled shafts for a project requires an up-to-date standard. The role of the standard in the...
Geotechnical Perspective?Proposed Drilled Shaft Standard
In the writer's understanding, a standard is an agreed upon manual of practice and as such, sets the level of performance and attainment considered adequate. A standard is...
A Structural Engineering Perspective for Drilled Shafts
This commentary is an attempt to close the gap between the Building Code Requirements for Reinforced Concrete (ACE 318-83) and the design of drilled shafts. The context of design includes...
Advanced Graphical CAD System for 3D Steel Frames
An innovative, advanced graphical computer-aided design system, called STEEL-3D, is described. The main objective of this program is to provide the engineer with all the tools necessary...
Return to search