Golden Gate Bridge Improvements
The Golden Gate Bridge, Highway and Transportation District engineer talks about improvements made to the Golden Gate Bridge since opening day. Improvements covered include: wind bracing,...
Building Constructed Up and Down at Once
The One Westwood Building, now going up in Los Angeles' suburban Westwood, is being built up and down from ground level simultaneously. The key was a slurry wall surrounding...
Computers: What Do Students Need to Know?
This article is based on interviews with three professors at three universities, a recent graduate from each school, and the graduate's employer. The interviews show that...
Automating Bridge Design
To avoid some of the pitfalls of manual design calculations, Parsons Brinckerhoff Quade & Douglas engineers designing a series of bridges for a $280 million section of the New...
Dam Safety Improvements for Tolt River Dam
Studies were performed to identify measures to improve the safety of the project under earthquake and extreme flood conditions while permitting the owner to store additional water under...
Comparison of Some River Discharge Calculation Methods
To measure the discharge of a river, it is necessary to develop a stage-discharge curve based on water velocity at various cross sections of the river. This is the method which is used...
Modification of Meander Pattern Using Wing Dams
A sharp river bend and a highway bridge together create potentially hazardous conditions for all down-bound barge tows on the Mississippi River at Lansing, Iowa. The tendency of the river...
LFRD Bridge Design as Viewed by the Designer
The load and resistance factor design (LFRD) design concept has been resisted by some bridge engineers on the grounds that it represents a reduction of the 'factor of safety'...
Evaluation of Corroded Steel Bridges
In the United States there is a large inventory of corroded steel bridges. The evaluation of these existing bridges is difficult when considering all the uncertainties involved in deterioration....
Steel Plate Girder Alternate I-10/I-17 Interchange
The scope of the Phoenix I-10 Viaduct allowed extensive study for the optimization of this moderate span steel plate girder bridge. The value engineering studies lead to the use of the...
Queensboro Bridge Inspection and Rehabilitation
An in-depth inspection of the Queensboro Bridge revealed deterioration of certain elements on the lower level of the main bridge. These elements include the outer roadway cantilever brackets,...
Prediction of Deformations Due to Heat Curving
This paper summarizes the state of the art in the thermal deformation techniques. Alternate analytical methods are described. The limitations and accuracy of these models are noted, and...
Design of Steel Transmission Pole Structures
This document has been carefully prepared in an effort to provide an authoritative source of information about effective design and fabrication of steel transmission pole structures. The...
Measures Against Wind-Induced Vibrations of Bridges
The design of very flexible structures, such as long-span steel bridges, are frequently governed by wind-induced vibrations. This paper introduces the present situation of the cable-supported...
The Behavior of R/C Pinned Bridge Columns under Lateral Loading
Four one-eighth scale one-way hinge details of the type used in highway bridges were tested to study the effect of combined shear and flexure caused by lateral loads. The aspect ratio...
Wind Tunnel Aeroelastic Model Study of the Baytown Bridge (Steel Alternative)
Analytical and full bridge aeroelastic model studies performed to assess the aerodynamic stability of the steel alternative Baytown Bridge over the Houston Ship Channel are described....
Dynamic Behavior of Three J.S. Cable Stayed Bridges
Dynamic considerations in the design of three recently designed cable stayed bridges are discussed. The presentation includes analysis for eigenfrequencies and eigenmodes, assessment of...
The Far? Bridge?Long Life at Low Costs
The superstructure of the bridge is a steel structure which proved to be competitive compared to the tendered concrete solution, due to simple and rational design both structurally and...
Methods for Improving the Seismic Response of Concentrically Braced Steel Frames
This paper briefly reviews various factors contributing to the poor performance occasionally observed in concentrically braced steel frame structures during recent earthquakes. Several...
The Design and Construction of the Washington State Convention and Trade Center Over Interstate 5
The Washington State Convention and Trade Center is a 10-level, 1,000,000-square foot facility constructed over Interstate 5 in downtown Seattle. The project spans over three city streets...
Return to search