High-Strength Concrete Joints Under Cyclic Loading
This experimental investigation was undertaken to check the validity for high-strength concrete beam-column joints of recommendations made by ACI-ASCE (American Concrete Institute-American...
Tuned Mass Dampers for Towers and Buildings
Tuned mass dampers (TMD's) are used to reduce the response of tall slender structures to resonant wind-induced oscillations. This paper reviews the authors' experience with the design...
Structural Design and Wind Resistance of Fukuoka Tower with T.M.D.
Fukuoka Tower, which was built in 1989, was projected as a monument, a observation tower and a broadcasting antenna with 234m high. In this tower, a Tuned Mass Damper(TMD) was set, in...
Long-Span Design for Seismic Forces?A Case Study of the Anaheim Arena
The design for the Anaheim Arena roof evolved in response to the strict requirements for a structure in a seismic zone 4 location. The support of the 329 ft. (100 m) by 444 ft. (135 m)...
Blast-Damaged Concrete Structures in Beirut
This paper describes the effect of blasting loads on structural members. It identifies predominant structural systems in war-damaged zones of Beirut and to explain typical damage mechanisms....
On the Numerical Simulation of Wind Loads on Structures
A new methodology for numerical simulation of 3-dimensional turbulent flow based on the use of a Galilean frame and the finite point method is presented. The pressure field of the solutions...
Structural Response Using Stiffness Decoupler
The structural properties of a new stiffness decoupler developed by Hu, Kirmser and Swartz at Kansas State University, and its applications as an energy absorber and a device to isolate...
Steel Plate Energy Absorbers for Improved Earthquake Resistance
This paper discusses results of an combined experimental and analytical investigation on seismic response of frame structures using welded steel triangular plates as added damping and...
Response of Equipment in Structures Supported on Resilient-Friction Base Isolators Subjected to Ground Motion
In this paper, the response of equipment in structures on a particular friction-type device, the resilient-friction base isolator, is examined. The R-FBI is composed of layers of Teflon...
Robust Control for Buildings Under Earthquake
Robust control techniques are applied to civil engineering structures subjected to earthquake excitation. Full state feedback and observer based control laws are used to reduce the response...
Passive Energy Dissipation Systems for Earthquake-Resistant Design
Passive energy dissipation devices, also known as supplemental damping devices, have been proposed as a means by which the earthquake resistance of a building can be substantially enhanced,...
Parametric Study of Structures with Added Viscoelastic Dampers
This paper presents the result of a parametric study on the seismic behavior of minimum weight-designed structures with and without added viscoelastic dampers. The structures are first...
Viscoelastic Dampers for Seismic Pounding Mitigation
A hysteretic model for viscoelastic (VE) damper is explained. The model accurately accounts for the effects of excitation frequency as well as temperature of the damper. Benefit of using...
Recent Developments in Seismic Isolation Technology
Large experimental research projects for isolators for both civil structures and nuclear reactor applications have been conducted at the Earthquake Engineering Research Center (EERC) over...
Mitigation of Wind-Created Risks During Construction
Wind damage to structures during construction has been found to be significant and often catastrophic. Structural failures are often the result of wind loads that are far less than the...
Development of Computer-Based Models of Standards and Attendant Knowledge-Base and Procedural Systems
Existing and new technology can be used to develop a new generation of standards that would allow designers to use complex standards efficiently, help standard-writing bodies to detect...
Axial Capacity of Concrete Infilled Steel Box Column with Biaxial Bending
The objective of this study was to investigate the feasibility of using the Bresler reciprocal load method to calculate the axial capacity of a concrete infilled steel box column subjected...
Design of Stay Cables
Cable stayed structures, consisting of slender superstructure, stay cables and pylons are optimal systems for long span structures with regard to design an economy. The important function...
Response of Concrete Filled Grid Decks Under Static Loads
This paper briefly discusses the bending strength and stiffness of concrete filled grid decks that are subjected to static loads. The influence of design parameters (traffic flow direction,...
Inelastic Bridge Rating Procedures for Steel-Girder Bridges
Current bridge rating procedures for steel beam and girder bridges ignore the ability of the structure to redistribute forces both longitudinally and laterally. When rating steel bridges...
Return to search