Reliability-Based Expert Systems for Optimal Maintenance of Concrete Bridges
In this paper ongoing research in the CEC supported BRITE/EURAM project P3091 is presented. In the project reliability based expert systems for inspection and maintenance of corroded reinforced...
Reliability of Highway Bridge Piers
Structural safety of reinforced concrete bridge piers supporting highway traffic is studied. Reliability indices for flexure, shear, and combined flexure and axial load limit states at...
Experimental Testing of Laterally Loaded Large Scale Bridge Abutments
The challenges to a bridge analyst in defining abutment boundary conditions and the current state of the practice are presented. Variables within the abutment system are defined and discussed...
An Information System on the Performance of Suspension Bridges Under Wind Loads
While most suspension bridges for which information is available, in operation between the period: 1701-1992, have performed satisfactorily under wind loads, a few bridges were destroyed,...
After-Fracture Response of a Two-Girder Steel Bridge
The I-40 bridges over the Rio Grande are due to be razed in mid 1993 due to geometry and traffic safety considerations. The bridges are classified as 'fracture critical' two girder steel...
Modal Analysis Technique for Bridge Damage Detection
The dynamic responses of a wide-flange steel beam with artificially introduced cracks were studied analytically and experimentally. Frequencies, displacement mode shapes (DMS) and strain...
Full-Scale Bridge Test to Monitor Vibrational Signatures
A full-scale highway bridge, in the process of being demolished and replaced was monitored using vibrational techniques in its in-service condition. The bottom flange and web of one fascia...
Damage Estimation of Existing Bridge Structures
During recent earthquakes, severe damage have been reported in many bridge structures. Regardless of many damaged structures, methods to identify damage of structures are still limited...
Finite Element Analysis of a Highway Bridge Hinge
A highway bridge hinge is a very important element in bridge design. It releases thermal stresses that may be developed in the superstructure or the substructure of a bridge. A common...
An Innovative Connection Detail for High-Rise Buildings
Composite columns consisting of hollow steel tubes filled with high strength concrete have been used in high rise building construction in the USA and Far East Asian countries. The focus...
Inelastic Behavior of Noncompact Steel Bridge Girders
This paper highlights the results from one of several finite element studies of the inelastic moment-rotation behavior of continuous-span non-compact bridge girders at interior-pier locations....
Composite Beams and Joists
Composite beams and joists used as flexural members in multistory steel-frame buildings are considered. Research results have shown that present design values for headed shear studs, used...
Wood Bridge Design Using AASHTO LRFD Specifications
A nationwide project to develop a load and resistance factor (LRFD) design edition of the American Association of State Highway and Transportation Officials (AASHTO) Standard Specifications...
Durability and Ductility of Advanced Composites
In recent years, several fiber reinforced composites have been successfully used as prestressing materials for demonstration highway structures. Since these materials are relatively brittle...
A Model Specification for Pultruded Structural Shapes: An Industry Collaborative
The use of pultruded products is steadily increasing. To support this growth, the industry has identified the need for a collaborative effort in developing standards that form a base line...
Flexural and Shear Behavior of Combined Concrete and Graphite Epoxy Beams
An experimental and analytical study of six graphite composite beams are presented. Four of the beams incorporated a reinforced concrete slab. The composite action and the effect of concrete...
Design Optimization of an All-FRP Short-Span Bridge
The objectives of this study are: a) to determine the feasibility of designing an all-FRP bridge, and b) to demonstrate the usefulness of optimization techniques in the design of FRP superstructures....
Nonlinear Analysis of RC Beams Using High Performance FRC Matrices
The results of a nonlinear analysis model of reinforced concrete beams using a high performance fiber reinforced cement based matrix, particularly SIFCON (Slurry Infiltrated Fiber Concrete)...
Analysis and Design of SFRC Structural Elements
This paper presents and validates practical methods for flexural, shear and torsional analysis and design of fibrous reinforced concrete structural elements. The effects of both fiber...
Steel Fiber Reinforcement in Structural Application
Ribbon Technology Corporation's use of steel fiber reinforced concrete in the construction of their new manufacturing and office facility in Gahanna, Ohio. Cost savings are obtained by...
Return to search