Sewer Construction Inspection and Testing
Sewer construction testing is the final portion of the team effort that started with the goal of meeting the requirement for a sewer system for the protection of health and environment....
Investigations into the Structural Performance of Clay Pipes
Over the past 8 years, the Clay Pipe Development Association (CPDA) has commissioned non-destructive physical testing of vitrified clay pipelines. The diameters of the pipes have varied...
Unique Installation Methods for Large Interceptor in Poor Soil Conditions
The construction of approximately 1. 5 miles of a major sewer interceptor in downtown Boston encountered some unique construction challenges. The entire route required dewatering during...
Experiences in Concrete Pipeline Construction in Ontario 158-1985
The paper discusses the title subject in terms of concrete pipe fabrication methods and plants, pipe jointing and jointing materials, and construction experiences in the Province of Ontario,...
Simplified Stress and Deformation Analysis for Pipeline Construction
This paper discusses the strength and deformation behavior of flexible steel pipes during pipeline construction. Some possible simple and quick solutions to these special design and construction...
A Practical Approach to Selection of Waterline Materials for Use in Expansive Soils
The authors previously investigated the performance of asbestos-cement, polyvinyl chloride and ductile iron pipe in the expansive soil environment. Expansive soil forces on the pipe were...
Bending Moment of Underground Flexible Pipes in a Centrifuge
The effect of several factors on bending moment of an underground flexible pipe section buried in a ditch with sheet piling was investigated experimentally by means of centrifugal model...
Stiffness Requirements for HDPE, Profile Wall Pipe
For the past two years the Gulf Oil Corporation has sponsored a research study on profile wall High Density Polyethylene (HDPE) pipe at Texas A & M University. A pipe design computer...
Investigation of the Long-Term Creep Modulus for Buried Polyethylene Pipes Subjected to Constant Deflection
The tests reported in this paper are simulating the stress relaxation in constantly deflected pipe rings of various high density and medium density polyethylene grades. The pipe rings...
The Relative Strain as a Design Criterion for Buried uPVC Gravity Sewer Pipes
When designing buried plastic sewer pipes, the relative strain caused by deflection of the circular pipe section is of particular interest. The reason for increased interest is the present...
Determining the In-Place Density of Soils Using the Sleeve Method
The sleeve method of determining the in-place density was developed by Bureau of Reclamation field personnel for cohesionless, fine, gravel soils used for pipe bedding when other methods...
Buried Fiberglass Pipe Response to Field Installation Methods
In 1970 near Yuma, Arizona, a field test installation of 30 inch diameter fiberglass pipe was constructed. Twelve years later the pipeline was remeasured. Measurements of pipe profile,...
Strains Induced by Combined Loading in Buried Pressurized Fiberglass Pipe
In 1983 Owens Corning Fiberglas and Utah State University collaborated on a study of combined strain behavior of fiberglass pipe to quantify the bending strain reduction as a function...
Buried Fiberglass Pipe Performance and Installation Requirements and Design Calculations in International Standardization
This paper elaborates on a proposed standard covering details of fiberglass pipe buried installation requirements and criteria for selection of pipe stiffness. It also discusses the selection...
Durability of Clay Pipe
Clay pipe, manufactured in accordance with ASTM C-700, has unusual resistance to attack by chemical agents. The pipe is highly stable in hydrochloric and sulfuric acid and subject to corrosive...
KEMCOR?A Chemical and Corrosion Resistant Piping System
KEMCOR is a new underground composite pipe system designed for chemical process use in such industries which require a high degree of corrosion resistance to varying concentrations and...
Response of Buried Flexible Plastic Conduits Under Loading
Structural performance of 75 mm and 100 mm diameter plastic conduits embedded in Lloyd clay were examined experimentally in a laboratory soil bin, and numerically by the finite element...
Large Diameter Plastic Pipe Design
This paper presents a rationale for the design of large diameter plastic pipes for gravity flow applications. This procedure, applicable for all plastic pipes, adapts state-of-the-art...
Successful Use of Centrifugally Cast Glassfiber Reinforced Plastic (GRP) Pressure Pipes for Public Works in Sweden
Centrifugally cast GRP pipes were introduced in Sweden 17 years ago for industrial applications mainly as a gravity pipe. The process of pipe manufacturing as well as the pipe itself and...
Design of Non-Pressure Very Flexible Plastic Pipe
There is considerable debate about the correct structural design procedure to be used for very flexible plastic pipe (VFP) - typically glass-fiber reinforced pipe (GRP), reinforced plastic...
Return to search