Geologic Assessment of Seismotectonic Hazards
Design and modification of dams require evaluation of potential seismotectonic hazards based on consideration of the historic earthquake record and deterministic evaluation of geologic...
Seismic Response Component in the Risk Assessment of Dams
The risk analysis model for dams that is discussed in this paper considers the probability of an initiating event and the following conditional probabilities of the system response, the...
Optimum Cut-Outs on Plate Stability
Cut-outs are unavoidable in some of the plate components. To minimize the plate weight, in the meantime, to maintain the critical buckling load as high as possible is one of the major...
Behaviour of Thin-Walled Channel Sections in Bending
The effects of local buckling on the behaviour and load carrying capacity of thin-walled cold formed steel plain channel sections is examined. The bending is applied in such a way that...
Simplified Steel Compression Member Design
The objective of this paper is to present a simplified method of designing steel columns subjected to axial loads and moments for use in situations where automated design methods are inappropriate....
General Considerations for Seismic Stability
The basic design consideration is provision of sufficient stiffness, strength and adequate ductility for the varied loads imposed on the building. Adequate stiffness is needed to resist...
Code Designed Steel Frame Performance Characteristics
Three similar steel ductile moment-resisting frame structures designed in accordance to the Uniform Building Code (1976-1985) are evaluated for their performance characteristics during...
Cyclic Behavior of Concrete-Filled Tubes
This paper presents the results of tests on hollow and concrete-filled rectangular tubes subjected to cyclic bending and buckling. It is shown that concrete infill greatly improves the...
Dynamic Simulation of Foundations on Winkler Subgrade
The objective of this paper is to present a dynamic simulation of foundations on Winkler subgrade. The analysis is based on a direct simulation procedure. The structures have been modeled...
Lateral Impedance of Contact Pile Foundations
The static and dynamic lateral impedance of pile foundations for which there is continuous contact between the bottom of the pilecap and the underlying soil is investigated. A parametric...
Risk Assessment for Cladding Panels: An Expert Systems Approach
Risk assessment for structures in the context of wind engineering involves many factors such as wind hazard, the wind sensitivity of the structure and the socio-economic value of the structure....
Assessment & Control of Wind Created Risk During Construction
Structures under construction have been damaged by winds. The damaging winds, typically, are much lower than the design wind loads for completed structures. Little guidance is available...
Performance of Viscoelastic Dampers in World Trade Center Towers
The viscoelastic damper was conceived and developed as a part of the structural design for the Twin Towers of the World Trade Center, New York. They are an integral and an essential part...
Transient Response of Wind-Induced Internal Pressures in Buildings
The paper refers to a new experimental approach applied in a boundary layer wind tunnel experiment to test the transient response of the wind-induced internal pressure in a building when...
Measuring the Spatial Characteristics of Unsteady Pressures
This paper has reviewed current methods of determining spatially-averaged time-varying wind loads on wind tunnel building models. Some of the possibilities opened by simultaneous multi-channel...
Improved Design Procedure for Shallow-Buried Structures to Resist Airblast Loading
Both conventional and nuclear weapons generate airblast loads of sufficient magnitude that structure survival at acceptable cost favors below grade construction. The design of shallow-buried...
Suspended Polycarbonate Shield to Defeat Terrorist Threats
The Navy Civil Engineering Laboratory is conducting research on a window concept that offers great potential for overcoming the disadvantages of blast resistant windows. The concept is...
Response Charts for Designing Against Nuclear Overpressures
The single-degree-of-freedom equation of motion for an elastic-plastic system with a nuclear airblast overpressure forcing function is nondimensionalized and solved. Solutions are presented...
Limiting Performance and Design by Reanalysis of Structures for Blast Resistance
Limiting performance is the absolute optimal response of a structure under a specified transient load. Reanalysis methods are computational techniques for analyzing locally modified large-scale...
Fault Identification by Seismic Impact Load Techniques
The propagation of seismic waves generated by impact loading across a normal fault in carbonate rock was investigated by the seismic refraction technique. The field records were reduced,...
Return to search