Experiences in Concrete Pipeline Construction in Ontario 158-1985
The paper discusses the title subject in terms of concrete pipe fabrication methods and plants, pipe jointing and jointing materials, and construction experiences in the Province of Ontario,...
Alternative Approaches for Waterhammer Analysis and Pipeline Protection
This paper provides a brief review of typical waterhammer problems and their solutions for pumping systems. Alternative approaches to identify and resolve design problems are discussed....
Longitudinal Prestressed Piping for District Heating
The design of recently installed hot water district heating systems in the United States is based on similar systems developed in Europe. Longitudinal prestressing is used in the design...
Modeling Failure Probability of Underground Pipes
Factors influencing the performance of underground gas pipes are identified through a literature search and contacts with several utility companies. These factors are categorized as (i),...
A Practical Approach to Selection of Waterline Materials for Use in Expansive Soils
The authors previously investigated the performance of asbestos-cement, polyvinyl chloride and ductile iron pipe in the expansive soil environment. Expansive soil forces on the pipe were...
Bending Moment of Underground Flexible Pipes in a Centrifuge
The effect of several factors on bending moment of an underground flexible pipe section buried in a ditch with sheet piling was investigated experimentally by means of centrifugal model...
Stiffness Requirements for HDPE, Profile Wall Pipe
For the past two years the Gulf Oil Corporation has sponsored a research study on profile wall High Density Polyethylene (HDPE) pipe at Texas A & M University. A pipe design computer...
Investigation of the Long-Term Creep Modulus for Buried Polyethylene Pipes Subjected to Constant Deflection
The tests reported in this paper are simulating the stress relaxation in constantly deflected pipe rings of various high density and medium density polyethylene grades. The pipe rings...
The Relative Strain as a Design Criterion for Buried uPVC Gravity Sewer Pipes
When designing buried plastic sewer pipes, the relative strain caused by deflection of the circular pipe section is of particular interest. The reason for increased interest is the present...
Determining the In-Place Density of Soils Using the Sleeve Method
The sleeve method of determining the in-place density was developed by Bureau of Reclamation field personnel for cohesionless, fine, gravel soils used for pipe bedding when other methods...
Buried Fiberglass Pipe Response to Field Installation Methods
In 1970 near Yuma, Arizona, a field test installation of 30 inch diameter fiberglass pipe was constructed. Twelve years later the pipeline was remeasured. Measurements of pipe profile,...
Strains Induced by Combined Loading in Buried Pressurized Fiberglass Pipe
In 1983 Owens Corning Fiberglas and Utah State University collaborated on a study of combined strain behavior of fiberglass pipe to quantify the bending strain reduction as a function...
Buried Fiberglass Pipe Performance and Installation Requirements and Design Calculations in International Standardization
This paper elaborates on a proposed standard covering details of fiberglass pipe buried installation requirements and criteria for selection of pipe stiffness. It also discusses the selection...
A Study of Inlet Control Alternatives for SWM
A laboratory study of alternatives for effecting inlet control on urban storm sewer systems for stormwater management (SWM) is described. The test facility was a full-size physical model...
Stress and Strain Responses of a Soil-Pipe System to Vehicular Traffic
A 16-in. natural gas pipeline near Racine, Wisconsin, had been in service for some 30 years. In 1982 road widening operations on a line parallel with the pipe presented the opportunity...
Durability of Clay Pipe
Clay pipe, manufactured in accordance with ASTM C-700, has unusual resistance to attack by chemical agents. The pipe is highly stable in hydrochloric and sulfuric acid and subject to corrosive...
KEMCOR?A Chemical and Corrosion Resistant Piping System
KEMCOR is a new underground composite pipe system designed for chemical process use in such industries which require a high degree of corrosion resistance to varying concentrations and...
Inspection/Condition Analyses of Large Underground Pipelines
Inspection/Condition Analyses of Underground Pipelines (sewers and conduits) will be a necessary function of the pipeline Owner/Operator. The Condition Analyses and Inspection phases are...
Field Testing of 84-Inch-Diameter Plastic Pipe
During the summer of 1981, a research project was initiated to monitor strains and deformation in 84-inch diameter RPM (reinforced plastic mortar) pressure pipe. Three 20-foot (6. 1-m)...
Response of Buried Flexible Plastic Conduits Under Loading
Structural performance of 75 mm and 100 mm diameter plastic conduits embedded in Lloyd clay were examined experimentally in a laboratory soil bin, and numerically by the finite element...
Return to search