Modeling Techniques for Seismic Analysis of Supported Systems
An automated seismic qualification process is presented which integrates the modeling and evaluation aspects of supported system design. Emphasis is placed on baseplate and joint design....
Analytical Solution of Cable Tray Hanger 3D Structural Interaction under Seismic Loading
Structural design of cable tray hangers is controlled by the Nuclear Regulatory Commission's stringent requirements of seismic analysis. A finite element space frame model...
Vibration Isolation of Cable Tray Hangers
Analytical and experimental investigations have been performed to partially evaluate the feasibility of using much more flexible support systems than those presently used to support electrical...
Piping Analysis: A Flexibility Approach
Design for the vertical and horizontal accelerations associated with a seismic event coupled with low allowable loads on equipment are two primary contributors to the current situation....
A Correlation Study on the Spectrum Decomposition Method
The major elements of the Spectrum Decomposition Method (SDM) are reviewed together with its automated process for generation of in-equipment response spectra (IERS). The floor required...
Fluid Structure Interaction Analysis of a Concrete Suppression Chamber of Mark I Containment System
Recent studies have demonstrated that the interaction between a structure and fluid can have a significant influence on the response of the overall system when subjected to certain dynamic...
A Pseudo Response Spectrum Method for Mark I Loads
A pseudo base motion response spectrum method is developed to uniquely evaluate the periodic condensation oscillation and chugging drag loads that may occur on submerged structures within...
Development of Concrete Nuclear Containment (ACI 359) Code Requirements as they Relate to Probability Based Load
The historical development of the load combinations used in concrete containment is presented in the paper. These load combinations are examined and identified in the light of the reasonable,...
Containment Integrity of SEP Plants under Combined Loads
The containment designs analyzed consisted of three inverted light-bulb shaped drywells used in boiling water reactor (BWR) systems, and three steel-lines concrete containments and a spherical...
Bayesian Procedure for Evaluation of Containment Capability
The functional requirements of a steel or concrete containment is to maintain the structural integrity as well as the leak-tight integrity of its pressure boundary under specified design...
Determination of Containment Vessel Ultimate Capacity Using Nonlinear Finite Element Analysis
Analysis of steel containment vessels is normally performed using linear elastic solutions with allowable stresses specified by applicable design codes. This method gives little indication...
Structural Performance Predictions for Liner Plates on Nuclear Facilities
The history of the use of liner plates is presented. It is shown that the liner plate can be buckled, and can be bonded or not bonded to the concrete. The buckled plate usually has bending...
Safety Investigations of Existing Spent Fuel Storage Structures for Increased Spent Fuel Storage Capacity
Delays in the solution of disposal problems continue to create the need for additional on-site spent fuel storage capacity at commercial nuclear power generating facilities. Rod consolidation...
Experimental Determination of Fluid-Coupling Coefficients in an Array of Hexagonal Prisms
The problem is related to the seismic analysis of fast breeder reactor cores, where the fluid trapped between the subassemblies is known to have a considerable influence on the core response....
Update on Impact Effects in Nuclear Plants Part II?Review of Pipe Whip Impact
Current regulations require that pipe breaks be postulated in high-energy lines and measures be taken to prevent consequent damage to essential structures and systems. The paper addressed...
Computer-Automated Limit-States-Design of Steel Frameworks
The paper concerns the computer-automated synthesis of minimum-weight planar steel frameworks. For any number of applied loading cases, the design of the structure may be constrained by...
Reliability-Based LRFD for Transmission Structures
A simple reliability-based Load and Resistance Factor Design (LRFD) method is proposed for the structural design of electric transmission lines. With the proposed method, the designer...
Plastic Design Requirements of the AISC Proposed LRFD Specification
The American Institute of Steel Construction proposed LRFD Specification (1) has recently completed a one year period of trial use and review. This paper discusses the background of the...
Finite-Strain Axial Analysis of Piles in Clay
In the late 1970's, a series of research projects developed simple effective-stress methods to predict the axial capacity of piles in normally-consolidated clay. The method...
Prediction of Settlement of Single Piles in Clay
Analyses by trial were used to fit theoretical load-settlement curves to measured curves for driven piles. For the elastic method, analyses of load tests indicated that designers should...
Return to search