Stiffness Requirements for HDPE, Profile Wall Pipe
For the past two years the Gulf Oil Corporation has sponsored a research study on profile wall High Density Polyethylene (HDPE) pipe at Texas A & M University. A pipe design computer...
Investigation of the Long-Term Creep Modulus for Buried Polyethylene Pipes Subjected to Constant Deflection
The tests reported in this paper are simulating the stress relaxation in constantly deflected pipe rings of various high density and medium density polyethylene grades. The pipe rings...
The Relative Strain as a Design Criterion for Buried uPVC Gravity Sewer Pipes
When designing buried plastic sewer pipes, the relative strain caused by deflection of the circular pipe section is of particular interest. The reason for increased interest is the present...
Determining the In-Place Density of Soils Using the Sleeve Method
The sleeve method of determining the in-place density was developed by Bureau of Reclamation field personnel for cohesionless, fine, gravel soils used for pipe bedding when other methods...
Buried Fiberglass Pipe Response to Field Installation Methods
In 1970 near Yuma, Arizona, a field test installation of 30 inch diameter fiberglass pipe was constructed. Twelve years later the pipeline was remeasured. Measurements of pipe profile,...
Strains Induced by Combined Loading in Buried Pressurized Fiberglass Pipe
In 1983 Owens Corning Fiberglas and Utah State University collaborated on a study of combined strain behavior of fiberglass pipe to quantify the bending strain reduction as a function...
Buried Fiberglass Pipe Performance and Installation Requirements and Design Calculations in International Standardization
This paper elaborates on a proposed standard covering details of fiberglass pipe buried installation requirements and criteria for selection of pipe stiffness. It also discusses the selection...
Durability of Clay Pipe
Clay pipe, manufactured in accordance with ASTM C-700, has unusual resistance to attack by chemical agents. The pipe is highly stable in hydrochloric and sulfuric acid and subject to corrosive...
KEMCOR?A Chemical and Corrosion Resistant Piping System
KEMCOR is a new underground composite pipe system designed for chemical process use in such industries which require a high degree of corrosion resistance to varying concentrations and...
Response of Buried Flexible Plastic Conduits Under Loading
Structural performance of 75 mm and 100 mm diameter plastic conduits embedded in Lloyd clay were examined experimentally in a laboratory soil bin, and numerically by the finite element...
Large Diameter Plastic Pipe Design
This paper presents a rationale for the design of large diameter plastic pipes for gravity flow applications. This procedure, applicable for all plastic pipes, adapts state-of-the-art...
Successful Use of Centrifugally Cast Glassfiber Reinforced Plastic (GRP) Pressure Pipes for Public Works in Sweden
Centrifugally cast GRP pipes were introduced in Sweden 17 years ago for industrial applications mainly as a gravity pipe. The process of pipe manufacturing as well as the pipe itself and...
Design of Non-Pressure Very Flexible Plastic Pipe
There is considerable debate about the correct structural design procedure to be used for very flexible plastic pipe (VFP) - typically glass-fiber reinforced pipe (GRP), reinforced plastic...
Influence of Frost Action on the Load Exerted on Buried Pipe
When work was started on revising the Swedish code for concrete pipes at the end of the 70's, a research project was carried out to evaluate the risk of increased load due...
Vertical Transport of Fine-Grained Sediments in Suspensions
Numerical-model sensitivity studies were made to determine the effect of bed flux on the vertical distribution of fine-grained material suspended in turbulent flow. The transport equation...
Aggregation and Consolidation of Phosphatic Clays
The consolidation behavior of aggregated phosphatic clays has been investigated using a bench scale centrifuge. It was determined that aggregation of the clays with phosphogypsum, a waste...
Tidal Inlet Sand Transport in Rollover Pass, Texas
For Rollover Pass, which is a man-made, artificially stabilized tidal inlet located on the upper Gulf Coast of Texas, the magnitude of the net sand transport through the Pass was estimated...
Numerical Modelling of Bed Evolution in Braided Channel Systems
The overall modelling approach adopted is based on an assumption of quasi-steady flow. The numerical algorithm is based on a split-operator approach, in which the flow energy equation,...
Planned Overtopping of Embankments Using Roller Compacted Concrete
Three recent projects are discussed where the economy and versatility of roller compacted concrete (RCC) were utilized to allow flood water overtopping of small to medium size embankment...
Design and Calibration of a 200-Foot Model Irrigation Border with a Computer Controlled Infiltrating Bed
A physical model of an irrigation border was constructed using a 200 ft long by 2. 5 ft wide tilting flume with a 3. 5 inch deep infiltrating gravel bed. The border was partitioned into...
Return to search