Update on Impact Effects in Nuclear Plants Part III?Review of Heavy Object Drop
The consequences of an accidental drop of a heavy component from a lifting device in a nuclear power plant are required to be evaluated even though the device may have been designed using...
Coupled Vertical-Rocking Response of Base-Isolated Structures
A base-isolated building can have a small horizontal eccentricity between the center of mass of the superstructure and the center of rigidity of the supporting bearings. The structure...
A Study of the Correlation of the Components of Instructure Motions During Earthquakes
Thirty-two buildings are selected that have all three components of motion recorded in the basement, midheight and top of the structure. The correlation coefficients of these motions,...
Modeling Techniques for Seismic Analysis of Supported Systems
An automated seismic qualification process is presented which integrates the modeling and evaluation aspects of supported system design. Emphasis is placed on baseplate and joint design....
Pipeline Hydraulic Transient and Leak Detection Analysis
Liquid and gas pipelines cannot be properly designed with consideration of steady flow analysis techniques alone due to the possibility of pipeline failure resulting from uncontrolled...
Computer-Automated Limit-States-Design of Steel Frameworks
The paper concerns the computer-automated synthesis of minimum-weight planar steel frameworks. For any number of applied loading cases, the design of the structure may be constrained by...
Reliability-Based LRFD for Transmission Structures
A simple reliability-based Load and Resistance Factor Design (LRFD) method is proposed for the structural design of electric transmission lines. With the proposed method, the designer...
Plastic Design Requirements of the AISC Proposed LRFD Specification
The American Institute of Steel Construction proposed LRFD Specification (1) has recently completed a one year period of trial use and review. This paper discusses the background of the...
Limiting Tip and Side Resistance: Fact or Fallacy?
The tip and side resistances of deep foundations do not reach a limit at a critical depth; instead, they increase with depth. For the tip, the rate of increase decreases with depth. For...
A Structural Engineering Perspective for Drilled Shafts
This commentary is an attempt to close the gap between the Building Code Requirements for Reinforced Concrete (ACE 318-83) and the design of drilled shafts. The context of design includes...
Advances in CAD for Structural Engineers
In the 1980's Computer-Aided Design (CAD) will offer the structural engineer an opportunity to improve his work. Decreases in the cost of equipment and improvements in computer-aided...
Turbidity Generated by a Model Cutterhead Dredge
The study of turbidity generation indicates that, in general, turbidity increases with an increase in the cutter speed and an increase in the cutter swing velocity. A silt curtain deployed...
Shoaling Problems and Improvements Sunny Point, North Carolina
The Military Ocean Terminal, Sunny Point (MOTSU), is located on the Cape Fear River, approximately 18 miles downriver from Wilmington, North Carolina. The facility has experienced significant...
Abrasion Resistance of Polyethylene Dredge Pipe
In recent years there has been a slow but steady increase in the number of dredges using high density polyethylene (HDPE) pipe in discharge lines. HDPE's increased popularity...
Sediment Resuspension from Dredging Activities
Dredges are a logical choice for removing contaminated sediments from our Nation's waterways. Historically, the dredging industry has emphasized increased production in an...
Influence of Roughness on Velocity and Dispersion at Low Flow
Dependence of the hydraulic and transport characteristics of low flow on channel roughness is investigated. Empirical expressions are used to estimate roughness coefficient as a function...
Buoyant Jet Solution with Synthetic Entrainment Function
A synthetic entrainment function is proposed for buoyant jets discharged at an arbitrary angle into otherwise quiescent ambient fluids. The entrainment function consists of two separate...
Effects of High Sediment Concentrations on Velocity and Sediment Distributions
Several classifications are required to describe sediment-transporting flow. The flow may be turbulent or laminar, Newtonian or non-Newtonian, and may also have a uniform or nonuniform...
High Sediment Concentrations Require High In-Channel/Supply of Sediment
Flows with high sediment concentrations (greater than 10 percent by weight) most commonly occur either as debris flows in steep channels throughout the world, or as hyperconcentrated flows...
Flow Parameters of Fluid Mud
A set of small-scale, high-resolution velocity and stress sensors based on rugged metal-clad hot wires and epoxy-encapsulated hot films is to be evaluated for its performance characteristics...
Return to search