Floating Bridge for 100 Year Storm
In 1979 the west half of the Hood Canal Floating Bridge, built in 1960, in Seattle broke up and sank during a storm that lasted eight hours with winds of 80 mph and gusts over 100 mph....
Shrimp Farm Made Feasible
Engineers on a limited budget developed a facility on the island of Oahu, Hawaii, where Mexican blue shrimp are being raised commercially. A series of U shaped sections were laid parallel...
Record Bridge Replacement
Jacks Run Bridge had to be rebuilt in one year instead of the usual two to three. So the Pennsylvania Department of Transportation spearheaded the quickest replacement of a major bridge...
Bridging Twin Ports
The Major Richard I. Bong Memorial Bridge, part of U. S. Highway 2, connects harbors at Duluth, Minn. and Superior, Wisc. The new highway link was designed to relieve congestion on nearby...
Who Should Design Bridges?
For many years Design-Build-Proposals have been common practice in Europe (except in the UK). Structures in these countries are 20% more economical than similar projects in the U. S.,...
Clay Pipe Installation?Advances in Load Factors
This report presents an evaluation of traditional load factor values for clay pipe and the development of a new bedding system which gives a higher load factor. Tests demonstrate that...
Failure of a Large Reinforced Concrete Pipeline
This paper describes the damage that occurred when a landslide overloaded an 11 ft diameter reinforced concrete pipeline. The 8 ft lengths of pipe, each of 11. 5-in. wall thickness, were...
SPIDA: An Analysis and Design System for Buried Concrete Pipe
The paper presents a description of a new computerized direct design method for buried concrete pipe named SPIDA (Soil-Pipe Interaction Design and Analysis). Also the technical basis and...
Experiences in Concrete Pipeline Construction in Ontario 158-1985
The paper discusses the title subject in terms of concrete pipe fabrication methods and plants, pipe jointing and jointing materials, and construction experiences in the Province of Ontario,...
Proportioning Reinforcement for Buried Concrete Pipe
The proportioning of reinforcement between inner and outer cages that is specified in ASTM Standard Specification C76 for concrete pipe in sewer and culvert applications is examined in...
Influence of Frost Action on the Load Exerted on Buried Pipe
When work was started on revising the Swedish code for concrete pipes at the end of the 70's, a research project was carried out to evaluate the risk of increased load due...
The Impact of the I-664 Bridge-Tunnel Crossing on Sedimentation
A sedimentation evaluation was made of the proposed I-664 Bridge-Tunnel complex across the James River, Virginia. This paper briefly describes the procedures used and the results obtained...
Planned Overtopping of Embankments Using Roller Compacted Concrete
Three recent projects are discussed where the economy and versatility of roller compacted concrete (RCC) were utilized to allow flood water overtopping of small to medium size embankment...
Investigation of Design Criteria for APM Guideways
Designers have relied mostly on the provisions of the American Association of State Highway and Transportation Officials (AASHTO) Standard Specifications for Highway Bridges. Sometimes...
Brazil's Innovation in APM Technology
The paper discusses an automated people mover (APM) called an Aeromovel which consists of pneumatically-controlled vehicles weighing less than 20,000 pounds with a capacity of 300 passengers....
Design and Fabrication of the Guideway Superstructure for the Miami METROMOVER
The guideways for the driverless rubber-tired vehicles are entirely aerial. As a result of severe restrictions on horizontal alignment and pier locations imposed by the downtown Miami...
Design and Construction of Guideway: Vancouver Advanced Light Rapid Transit
The Vancouver Advanced Light Rapid Transit (ALRT), system consists of linear induction motor driven, light-weight cars automatically controlled operating over a 21. 4 km system from downtown...
Alignment Special Structures for Vancouver's ALRT
This paper describes the special long-span structures, offset columns, and bent structures used in situations where the standardized guideway components used in over 90 percent of the...
Production of Guideway Beams for the Vancouver ALRT
This paper describes the planning, layout and design of a large scale precast plant and innovations in production technology for the fabrication and delivery of 1040 tangent and curved,...
Guideway Beams?Formwork and Fabrication
A manufacturing concept was developed around an adjustable form capable of mass producing prestressed concrete beams to the unique geometric configuration of each section of track. The...
Return to search