Behavior of an Operating Floor Subjected to Heavy Load Drops
A structural evaluation of the behavior of a Boiling Water Reactor operating floor subjected to postulated heavy load impact is presented relative to the evaluation of nuclear industry...
Computer-Aided Load Monitoring System for Nuclear Power Plant Steel Framing Structures
The design of nuclear power plant steel framing structures is a long and involved process. It is often complicated by numerous changes in design loads as a result of additions, deletions...
Computer-Aided Design (Seismic Qualification) of Cable Tray Support System ? CADSTrays
A computer system for the analysis and design of cable tray hangers for nuclear power generating plants is discussed. An interactive language for the CADSTrayS was developed. Application...
Sensitivity of Peak Dynamic Responses to Input Factors
Responses have been calculated for the Zion Unit 1 plant, using the SSMRP computer code SMACS, as part of the seismic probabilistic risk assessment performed by the Seismic Safety Margins...
Treatment of Design and Construction Errors in PRA
The risk estimates developed in a PRA should allow for potential design and construction errors. These errors generally modify the component responses and fragilities. Since most design...
Seismic Evaluation of Reinforced Masonry Walls
Masonry walls in operating nuclear plants are in many cases found to be overstressed in terms of allowable stresses when evaluated using current seismic design criteria. However, experimental...
The Use of Joint Reinforcement in Qualifying Masonry Walls in Nuclear Power Plants
Wire joint reinforcement has been traditionally used in block masonry walls for crack control and to provide continuity for multiple wythe walls. In a number of nuclear power plants, vertically...
Probabilistic Seismic Analysis of a Nuclear Power Plant Steel Containment
Concern for the safety of nuclear power plants has motivated efforts to determine the statistical characteristics of the seismic resistance of steel containments under various types of...
Enhancing Quality of Construction on Nuclear Facilities
From the author's viewpoint and the viewpoint of others, the quality of construction on both nuclear projects and many other non-nuclear projects has decreased. The trend...
Techniques for Automating the Process of As-Built Reconciliation
The approach utilizes an electronic digital 'ruler' capable of measuring distances to 100 feet with a resolution of 1/100 of a foot. This ruler interfaces to...
Desin Control for Nuclear Power Plant Modifications
Modifications to operating nuclar power plants which impact structural components must be performed in a manner that is consistent with the licensing basis and technical specifications...
New Developments in Seismic Analysis of Primary and Secondary Systems
This paper presents recent advances made at NCSU in the seismic analysis of these systems. Algorithms are presented by which coupled mode shapes and frequencies can be evaluated without...
Integrated Testing and Analysis
This paper represents a new approach which greatly streamlines the entire process. In those cases where finite element modeling is used without test verification, the procedure consists...
Design Verification of HVAC Duct Turning Vanes in Nuclear Power Plants
HVAC ducts in nuclear power plants utilize short radius elbow construction with turning vanes to minimize the space requirement for duct work and to reduce flow losses in the elbows. Turning...
Evaluation of the Ultimate Pressure Capacity of Rectangular HVAC Ducts for Nuclear Power Plants
Structural design criteria are presently based on the AISI Code which limits the duct panel width-to-thickness ratio to a maximum of 500 and the maximum height-to-thickness ratio to 200,...
Strength and Stiffness Characteristics of Steel Ladder-Type Cable Trays
Ladder-type cable trays identical with the as-built are generally tested to establish their strength and stiffness characteristics. Test data for systems in operating plants, however,...
Vibration Isolation of Cable Tray Hangers
Analytical and experimental investigations have been performed to partially evaluate the feasibility of using much more flexible support systems than those presently used to support electrical...
Piping Analysis: A Flexibility Approach
Design for the vertical and horizontal accelerations associated with a seismic event coupled with low allowable loads on equipment are two primary contributors to the current situation....
Composite-System Approach for Seismic Analysis of Secondary Systems
An accurate and efficient method for seismic analysis of multiply supported, multi-degree-of-freedom secondary subsystems is developed. The method accurately accounts for the effects of...
A Correlation Study on the Spectrum Decomposition Method
The major elements of the Spectrum Decomposition Method (SDM) are reviewed together with its automated process for generation of in-equipment response spectra (IERS). The floor required...
Return to search