Chemical Resistance of Thermosetting Resins Used for Cured-in-Place Pipe
This paper summarizes the chemistry, short term physical properties, and long term chemical resistance for representative epoxy vinyl ester, epoxy, and polyester resins that are currently...
Accessibility of Geotechnical Earthquake Engineering Data and the Need for Data Storage and Dissemination Standards
Ease of data access and data standards are two issues critical to the success of GIS technology when applied to earthquake hazards research problems that require geotechnical engineering...
Assessment and Repair of Fire-Damaged Concrete Structures
Concrete, even though it may be the most fire-resistant of all the major building materials, can be damaged by fire. Seldom does even a major fire cause total destruction, however, most...
Seismic Design of Multi-Story, Wood-Framed Buildings
The seismic design and analysis of wood-framed structures is relatively simple; however, the challenges that present themselves within this design medium are shear and overturning force...
LRFD for Timber Structures
The use of load and resistance design (LRFD) methodologies is increasingly becoming the standard analysis procedure for engineering design. The concrete industry has used a variation of...
Structural Fire Resistance Design of Wood Beams and Columns: A Comparison of European and North American Practices
North American and Eurocode design methods for fire-resistive exposed wood members provide a very good example of the translation of research into practical engineering design procedures....
Drilled Shaft Side Resistance in Clay Soil to Rock
An evaluation is made of available field load test data for the axial side clay soils to hard rocks. Conventional total stress interpretations by the alpha method are used to examine the...
Side Resistance of Drilled Shafts in the Denver and Pierre Formations
Results of load tests on drilled shaft foundations in Upper Cretaceous shales are described and evaluated. Three load tests were conducted on shafts in the Denver Formation, in Denver,...
Behavior of Instrumented Model Piers in Manufactured Rock with a Soft Layer
A laboratory test apparatus has been used to study the side resistance of piers socketed into manufactured soft-rock masses. The results of four tests are reported, three of which included...
Strength Design for Reinforced-Concrete Hydraulic Structures
21st Century Timber Engineering
Timber engineering is moving into the 21st Century faced with challenges in technology, governmental mandates and environmental concerns. Engineers are continuously being challenged in...
On the Influence of Seismically Induced Residual Forces on Bridge Abutment Design
The seismic design of bridge abutments depend on the anticipated movement of the abutment during the design earthquake. For seat-type abutments in which the backfill resistance can be...
Improved Time-History Analysis for Structural Dynamics Calculations
Methods are developed to reduce the computational effort in time-history analysis of nonlinear structures. The methods permit use of much larger time intervals than are possible in conventional...
Shear Resistance Models for Concrete Bridges
Statistical models are developed for the shear resistance of concrete bridge girders. Two structural types are considered: reinforced concrete T-beams and prestressed concrete AASHTO girders....
Structural Control Under Stochastic Seismic Loads
This paper presents a method of controlling nonlinear and hysteretic civil engineering structures subjected to stochastic earthquake ground excitations. Emphasis is placed on control of...
Fuzzy Measures in the Knowledge Based Diagnosis of Seismic Vulnerability of Masonry Buildings
Rules based expert systems and fuzzy logic have been employed to increase the speed and the reliability of the survey of masonry buildings, to forecast their seismic vulnerability....
Structural Reliability of Seismic Isolation System
Seismic reliability analysis of isolated structure is conducted. In this study focused on are bearing capacity of isolation layer considering strength randomness of isolation bearings...
Reliability-Based Specification for Engineered Wood Construction
A three-year, industry-sponsored effort has resulted in the development of a reliability-based, load and resistance factor design (LRFD) Specification for wood construction. Improvements...
Load Duration and System Effects in LRFD for Wood Construction
The wood industry is developing a Load and Resistance Factor Design (LRFD) speciification for wood construction using probabilistic concepts. An analysis based on statistical models for...
Sampling Techniques for Time-Variant Reliability Problems
Time-variant structural reliability problems arise when the structural resistance may change with time (such as in structural deterioration) or when the system is acted upon by two or...
Return to search