Basic Aspects of Damage Mesomodelling
The basic aspects of a general damage computational approach which enable to simulate the complete fracture phenomenon are presented. It is a semi-discrete modelling where the material,...
Damage Mechanics Modeling of the Cyclic Behavior of Plain Concrete
The sudden stiffening behavior of concrete under cyclic loading is discussed and the available experimental investigations to delocalize damage is reviewed. A discussion on the applicability...
Three-Dimensional Fracture Process Zone Detection in Concrete
Process zones in concrete have been under intensive investigations during the past several years. Techniques have successfully been used to detect and map the 2-D superficial process zone....
Determination of In-Situ Stresses From Acoustic Emissions
Acoustic emissions (AE) are microseismic activities that are generated in concrete by cracking and damage. The rate of Acoustic Emissions, called the 'Event Rate', can provide indication...
Evaluating Polymer Concrete Bridge Expansion Joints Using Acoustic Emission
This study is to simulate the acoustic emission (A/E) of polymer concrete bridge expansion joints subjected to controlled representative loads by a rotating test apparatus on a circular...
Micromechanical Simulation of Wave Propagation in Dense Granular Assemblies
Two-dimensional DEM with modified Mindlin's contact law has been used to study the load transfer mechanisms in 'consolidated' granular assemblies. Results of simulation are presented and...
Neural Network Modeling of the Mechanical Behavior of Sand
Given a set of triaxial test data, an artificial neural network (ANN) has been trained to model the mechanical behavior of a medium-to-fine sand. Once trained, the ANN was tested by simulating...
Computer Simulation of Direct Shear Test
This paper presents a pilot study of a computer simulation of direct shear test on sands using the Discrete Element Method. The numerical test setup is described first, which is followed...
Stochastic Modeling of Fatigue Crack Growth with Retardation
This paper develops a new methodology for modeling fatigue crack growth accounting for both material inhomogeneity and the random nature of the loading process by modeling the crack growth...
Probabilistic Micromechanics in Constitutive Modeling of Granular Material
This paper gives a review of newly developed probabilistic methods for analysis of the effect of randomness in geometry and physical properties at the microscale on their macroscale response...
Joint Network Modeling and Scale Effects in Rock
Joint networks play a vital role in the mechanical and hydraulic behavior of rock masses. A realistic representation of joint geometry in rock masses and correct understanding of the mechanical...
Constitutive Modeling for Material with Perfect Disordered Heterogeneity
Finite element analysis with large number of elements are performed to simulate perfect disordered heterogenous material. The probabilistic nature of the micromechanical behavior of the...
Vortex Suppression in Wet-Pit Pump Intakes
Two distinct examples to suppress both air-entraining and boundary-attached subsurface vortices in large vertical pump intakes are presented that were developed by means of hydraulic model...
On the Modelling of Damage Due to Volumic Variations in Cementitious Composites
Two kinds of volumic variations are considered. Those due to thermal gradients on hardened concrete and those due to hydration processes at early ages. Models based on damage mechanics...
Strain-Based Damage Deactivation in Concrete
Motivated by the 'mode I' microcrack opening and closing mechanism, a procedure for the deactivation of the damage is developed. Strain based projection operators are used to negate the...
Automated Identification of Compression-Induced Cracking in Cement Paste
The development of image analysis techniques to identify cracks using scanning electron microscope images of hydrated cement paste is described. Cracks are identified based on both the...
Dugdale Model Applied to Crack Interactions
It is doubtful that modelling crack interactions problem within the context of elasticity adequately reflects the physical aspects as the failure of brittle material is approached. A model...
Contact Induced Damage
Contact induced damage is an important source of potential failure of engineering components. The particular applications where this damage occurs are in the automotive, aerospace and...
High-Resolution Interwell Seismic Experiments in Sedimentary Formations
High-frequency interwell seismic data were acquired to examine full waveforms recorded in the pulsed mode and in the swept mode as well as to perform traveltime inversion tomography for...
Estimating Damage and its Influence on Fracture Toughness
To estimate damage in a quantitative manner, a technique used whereby six values of linear strain are measured on a material element as a function of hydrostatic pressure. The high precision...
Return to search