Computational Open-Channel Hydraulics for Movable-Bed Problems
As a major branch of computational hydraulics, notable advances have been made in numerical modeling of unsteady open-channel flow since the beginning of the computer age. According to...
The Effect of Aeration on Scour
A vertical water jet was used to study the effects of entrained air, tailwater depth, size of bed material, jet diameter, and jet velocity on scour. Small amounts of entrained air were...
Evaluation of the Potential for Release of Residual Coal Tar by Flood Scour at a Superfund Site
To address the potential for release of residual coal tar by flood scour, stream cross-sections, stream discharge and sediment grain size data were collected during the Remedial Investigation...
A Generalized Diffusion Wave Flood Routing Model
A generalized diffusion wave model for flood routing is presented. The model can incorporate detailed data on natural cross sections and river bed geometry. An accurate numerical method...
The Calculation of Flushing Flows for Gravel and Cobble Bed Rivers
Flushing flows are needed to remove fines and sand from a gravel or cobble bed river. A natural stream will have periodic high flows adequate for flushing of fines and sand, but the hydraulic...
Geomorphic and Sedimentologic Evaluation of a Proposed Flood Control Project, Truckee River, Reno, Nevada
Geomorphic observations, sediment data and shear stress analyses were integrated to evaluate the potential responses of the steep, coarse grained Truckee River to a proposed flood control...
Longitudinal Channel Response Due to In-Stream Mining
This paper describes the analysis procedure developed for the Arizona Department of Transportation for the estimation of short-term longitudinal channel response due to in-stream mining....
Flow Transitions Around a Single Large Bed Element
A qualitative description of the characteristics of supercritical-to-subcritical flow transitions due to the presence of a single large bed element (LBE) in a laboratory flume is presented....
Sediment and Aquatic Habitat Associations in River Systems
This paper results from the Task Committee's effort to summarize knowledge linking sediment transport and aquatic ecology. This paper presents one element of this work: the...
Sediment Transport, Hydraulic Retention Devices, and Aquatic Habitat in Sand-Bed Channels
Streams and rivers of all sizes and in all parts of the United States flow on sand-bed channels. Scour, Transport, and deposition of sediments particles are natural processes in these...
Sediment Transport and Aquatic Habitat in Gravel-Bed Rivers
Gravel-bed rivers experience dymanic conditions of flow and sediment transport. Long periods of bed stability are interrupted by shorter periods of bed mobility when major changes and...
New Outlines for 500 kV Transmission Towers Using Cold-Formed Shapes: The Experimental Line of the American Electric Power Research Institute
The use of cold-formed steel members, in electrical transmission towers, is actually a feasible, reliable and economical solution. The EPRI experimental line is an example of the newest...
Design Issues in Steel Buildings
The Committee on Design of Steel Building Structures of the Committee on Metals of the Structural Division of ASCE was formed in 1981, with the express purpose of studying problems that...
Steel Girt Design
Procedures are presented for the design of light gage cold formed girts and hot rolled girts. The effects of continuity, sag rods, and wall sheeting are discussed. Design procedures are...
Behavior of Cold-Formed Steel-Concrete Composite Beams
An experimental investigation was conducted at California State University - Long Beach to study the structural behavior of composite beams made of thin-walled cold-formed steel stiffened...
Cold-Formed Z-Sections Under Axial Load and Bending
The use of cold-formed Z-section members as beam-columns presents some unique design problems which are not adequately addressed in the current design specifications. If these members...
Automated Load Capacity Determination of Cold-Formed Steel Compression Members
This paper presents an automated approach for the evaluation of the axial load capacity of nine cold-formed steel sections according to the latest AISI-1986 Cold-Formed Steel Specification....
Weathering Steel Bridges ? State of the Art
State of the art dissertations on materials that have been in commercial use for over a century are not likely to illustrate major new and innovative breakthroughs. Instead, the state...
On-Site Incineration
A variety of equipment is now available for incinerating hazardous wastes in situ. Thermal treatment, compared to land disposal, offers limited liability and immediate destruction. It...
Steel Structures
The seventy-eight papers included in this volume cover the fifteen sessions generally associated with steel structures presented at the Seventh Annual Structures Congress held on May 1-5,...
Return to search