Project Layout
Microtunneling projects should be laid out with attention to the benefits and constraints unique to this construction process. The following recommendations address some of these concerns:...
Shaft Considerations
Jacking and receiving shaft locations should be selected to minimize the number of shafts and disruptions while not exceeding the practical limits of the drive lengths achievable for a...
Microtunneling Operation
The shaft should provide safe working conditions and fully support the ground. Jacking and receiving shaft support system and sizes are typically determined by the contractor. See Chapter...
Shafts/Temporary Structures
Shafts should be of a size to accommodate the equipment and pipe selected and to allow for safe working practices. If the shaft must accommodate the permanent works, it is the contractor's...
Deep Freeze
In engineering, overcoming a failure can sometimes be more instructive than completing a project with unqualified success. Such was the case with the collapse and repair of a force main...
Turning with the Wind
A 125-m high tower built at the site of the Glasgow Science Center in the United Kingdom required some innovative design methods. To reduce the aerodynamic effects imposed on the slender...
Great Excavations
By any definition, the scale of the underground caverns being excavated near Geneva at the particle physics center run by the Conseil Europ�en pour la Recherche Nucl�aire (CERN)�the European...
New Bern Bypass
To alleviate congestion and offer tourists easier access to their destinations, the North Carolina Department of Transportation decided to reroute U.S. Route 17 out of the historic town...
Testing the Load (Available in Geoenvironmental Engineering Special Issue only)
The Pittsburgh District of the U.S. Army Corps of Engineers recently began construction of a new gated dam to replace a nearly 100-year-old concrete fixed-crest dam on the Monongahela...
Alaska's Last Link
Alaska's Seward Highway has been upgraded this past year. The last section of the highway dates back to the state's early mining days in the Kenai Peninsula,...
Below Boston's New Bridge
The Charles River Bridge, a 10-lane cable-stayed structure will be the widest cable-stayed bridge in the world. The bridge is 1,460 ft long with a main span between towers of 745 ft. This...
Construction Through Crude Oil
When the Hilltop Interceptor project in Cleveland confronted oil-saturated sandstone, designers had to rethink their shaft construction and support procedures. Among the hazards were volatile...
The South Bay Ocean Outfall
For more than 60 years, raw sewage has flowed down the hills of Tijuana, Mexico into the Tijuana River, crossing the U.S.-Mexican border. The sewage contaminates the low-lying river valley...
Recasting a Foundry (Available only in
Even as the Philadelphia Naval Shipyard sails toward closure under the 1991 Base Realignment and Closure Law, work at the base foundry has accelerated since the 1980s. The foundry uses...
Practical Guide to Grouting of Underground Structures
This book presents a hands-on discussion of grouting fundamentals and provides a foundation for the development of practical specifications and field procedures. The author takes a practical...
In the Wet
The concept of using large diameter vertical cylinder piles of steel and concrete is not new. Vertical cylinders constructed in pneumatic caissons go back at least 70 years. Steel cylinders...
Hydraulic Design of Spillways
Technical Engineering and Design Guides, as adapted from the U.S. Army Corps of Engineers, No. 12. This manual presents guidance for the hydraulic...
Numerical Modeling of Initial Ground Movement in an Instrumented Superconducting Super Collider Shaft
A 5.5 m diameter shaft was sunk into a rock formation of Taylor Marl to a depth of 61 m at the Superconducting Super collider (SSC) site. Numerical modeling using finite difference analysis...
Testing and Predicting the Movement of a Drilled Shaft in New Mexico
The New Mexico State Highway and Transportation Department (NMSH&TD) have been using drilled shafts for supporting bridges in the State of New Mexico. Several drilled shafts were...
The Tip Displacement of Drilled Shafts in Sands
The design load of large diameter drilled shafts is determined so that the settlements do not exceed the values associated with the ultimate and serviceability limit states. Based on the...
Return to search