A Critique of the Ultrasonic Pulse Velocity Method for Testing Concrete
The pulse velocity method is the most widely used ultrasonic nondestructive method for assessing concrete quality. However, it has been well established that the relation between ultrasonic...

Evaluation of Compressive Strength for High-Strength Concrete by Pulse Velocity Method
Development of compressive strength and pulse velocity for high-strength concrete from the age of 5 hours are studied in relation to cementitious material types and curing conditions....

Condition Monitoring of Structures Using Transient Response
Condition monitoring of structures by measuring transient response and tracking the derived modal parameters has been applied with success in three laboratory studies. Where modal parameters...

Numerical Simulation of Dynamic Shear Transfer
This study was focused on the dynamic response of concrete interfaces under the effects of impulsive loads, and the relationship between the interface shear transfer and the response in...

Nondestructive and Destructive Testing of a Three Span Skewed R. C. Slab Bridge
A three span, skewed, reinforced concrete slab bridge was field tested to destruction by the authors. Before the actual destructive test, nondestructive tests were performed to determine...

Simulated Field Trials of Non-Destructive Concrete Test Methods for Highway Structures
The data presented results from a two year Strategic Highway Research Program investigation into suitable NDT methods for determining the early age, and residual strengths of highway structures....

Nondestructive Crack Identification by Acoustic Emission Analysis and Ultrasonic Frequency Response
Nondestructive evaluation (NDE) by the acoustic emission (AE) analysis and the ultrasonic testing (UT) on the spectral (frequency) response is studied to identify crack geometry. AE waveform...

Review of NPP Concrete Degradation Factors and Assessment Methods
Degradation of concrete in nuclear power plant (NPP) structures can be an age-related phenomena. Several research programs have been initiated by the U.S. Nuclear Regulatory Commission...

Pullout Testing of High-Strength Concrete Members
An experimental investigation of a high-strength concrete mixture was undertaken to measure and evaluate pullout and compressive strength properties. Two columns, a slab, and cylindrical...

Concrete Surface Characterization Using Optical Metrology
The displacement of the surface of a concrete specimen is measured as it cures using an optical method. This method, known as optical metrology, is one in which a line is projected onto...

Shrinkage Measurements in Composite Beam Slabs
When the concrete slab on a composite beam shrinks, it is restrained by the steel beam to which it is connected. Tensile stresses, as a result, are developed in the restrained concrete...

On the Role of Experimental Mechanics in Assessing the Performance of Concrete
The role of experimental mechanics in material characterization, design, construction, performance evaluation, repair, rehabilitation and finally destruction of concrete structures is...

Quantitative Stereology of Concrete Microcracking
Stereological methods enable extrapolation of quantitative microcrack characterization from two dimensions to three dimensional space. However, because these quantifying techniques are...

Fracture Surface Characterization of Concrete
The objective of this paper is to characterize fracture surfaces of concrete, with varying maximum aggregate sizes dmax, by utilizing the concept...

Experimental Determination of the Relation Between the Damaged Zone and the Aggregate Size in Concrete Through Acoustic and Mechanical Techniques
The size of aggregates in concrete has an influence on the behavior of the material. The width of the localized band can be related to this characteristic. Different experimental techniques...

Behaviour of Prestressed Concrete End Blocks
This paper briefly reports on a series of experiments carried out on strip-loaded prestressed concrete end blocks. The results show that corresponding design methods presently used in...

Mechanical Characterization of the Soft Tissue in Horse Hooves
The laminar corium tissue of the equine distal digit (or horse hoof) has been tested uniaxial tension. The laminar corium tissue lies between the hoof wall and the underlying bone of the...

Use of Hierarchical Lattices for Predicting the Fluid or Stress Transfer in Concrete
Hierarchical lattices are used to study the influence of local disorder on the transfer of properties (stresses, strains, permeability) from the micro-scale to the macro-scale. They are...

Nonlinear Behavior of Thin Slender Free Surface Non-Newtonian Elliptical Rings
This paper analyzes the nonlinear motion of a slender concentric thin elliptical ring of an incompressible, non-Newtonian fluid. This study includes the physical effects of surface tension,...

Comparative Evaluation of Plasticity Theories Against Tension-Torsion Test at Finite Strain
This paper investigates and evaluates three hardening theories against a variety of nonproportional loading experiments on tubes made of annealed copper. It was concluded that the isotropic...

 

 

 

 

Return to search