Avoiding Lengthy and Costly Litigation by Negotiating Alternative Dispute Resolution Methods
A 'hot issue' in the construction industry today is the negative aspects perceived from wide arbitration use over the last 15 years. Although hearings usually...
Techniques of Negotiation
Three primary qualities are necessary for effective negotiation: knowledge, attitude, and skill. The author's firm has successfully used a negotiating team approach. This...
Embankment Seepage Control Design and Construction
For seepage control features of embankment dams, design criteria and construction practice is reviewed as it is reflected in the experience of the U. S. Army Corps of Engineers. The generally...
Designing and Monitoring for Seepage at Calamus Dam
Given the complex, pervious nature of the foundation for Calamus Dam, every effort has been made to incorporate design features that will reduce and control the anticipated large volumes...
Computer-Assisted Grouting Evaluation Systems
Electronic monitoring of cement pressure grouting at Ridgway Dam provides a powerful tool for geologic assessment of drilling and grouting results. Graphic surveillance and analysis of...
Some Aspects of Analysis and Prediction of Subsidence
A procedure based on the nonlinear finite element analysis was investigated for the prediction of subsidence caused by longwall mining. This paper presents a case study involving predictions...
Application of a Three-Dimensional Coupled Finite Element?Boundary Element Method
Three-dimensional conditions in underground construction occur at the face of a tunnel, at intersections of underground openings and around roughly equidimensional openings. As long as...
Nonlinear Fracture Process Zone in Rock
A study of the fracture process zone was conducted to gain an understanding of the physics of crack propagation in rock. The nondestructive testing technique of acoustic emissions was...
Oil Shale Fracture Characterization by a New Model
Fracture toughness of oil shale is a property which is essential for fracture characterization needed for energy resource development and recovery. However, a data base for fracture toughness...
Prediction of Highway Construction Noise Levels
A model for the prediction of noise levels from highway construction operations has been developed under sponsorship of the Federal Highway Administration (FHWA). Noise sources are geometrically...
Noise and Air Blast from Construction Blasting
Noise generated by construction blasting differs from other construction noise because of its frequency content. The audible high frequency portion is accompanied by a non audible, lower...
Cost Assessment of Construction Noise Control
The results of a series of studies have provided noise control engineers with a method to estimate off-site construction noise levels and the cost of reducing these to acceptable levels....
Noise Assessment, Measurement, and Mitigation, an OSHA View
A discussion is presented on the Occupational Safety and Health Administration (OSHA) 29 CFR 1910. 95 General Industry noise exposure standards and the 29 CFR 1926. 52 and 1926. 101 Construction...
A Tale of Six Cities
Battle Creek is a four mile urban stream that had an erosion problem that was accelerating with urbanization of its watershed. Erosion created unstable ravine slopes over 60 feet high,...
Proposed Design Criteria for Composite Steel Deck Slabs
Composite steel deck slabs have continued to gain popularity; today they are one of the predominant means of floor slab construction in most typical buildings. The term 'composite...
Composite Bridge Design in Germany
A span length between 40 m and 12 m has been regarded as optimal up to the mid-60's for a composite design to compete with prestressed concrete or steel alternatives. With...
Dynamic-Fatigue Response of Continuous Composite Bridges
The dynamic response of continuous composite bridges and the influence of fatigue loading at resonance frequency on the structural response are investigated. It is shown that cracking...
The Eurocodes and Shrinkage in Composite Beams
The two parts of this paper relate to different aspects of design procedures for composite structures of steel and concrete. First, recent developments in the coordination of the eight...
A History of Adhesive Bonded Composite Members
The history and development of adhesive bonding in composite members is traced. Two forms of composite members are explained. Research from different parts of the world is compared. Applications...
Mixed Systems: Past Practices, Recent Experience, and Future Direction
A comparison is made between composite column capacities derived from the authors procedure utilizing the ACI (America Concrete Institute) code requirements, and previously published semi-empirical...
Return to search