Joint Design in Composite Columns/Steel Beam Structures
The use of a composite building system, utilizing a composite exterior column and a concrete spandrel beam system, proposed by Dr. Fazlur Khan in 1967, is recalled. In the last 25 years,...
Axial Capacity of Concrete Infilled Steel Box Column with Biaxial Bending
The objective of this study was to investigate the feasibility of using the Bresler reciprocal load method to calculate the axial capacity of a concrete infilled steel box column subjected...
Concrete Arch Bridges for Supporting Steel Conduits of Mingtan Pumped Storage Project
For the Mingtan Pumped Storage Project of an installed capacity of 1600 MW, two parallel waterways have been constructed for conveying flows between the upper reservoir and the lower reservoir...
Lateral Bracing of Plate Girders Using Deck Forms
The initial results of a study of the ability of stay-in-place steel deck forms to stabilize bridge girders during construction is presented. The analytical and experimental results to...
Long Life Fatigue Behavior of Welded Steel-Bridge Girder Details
The Federal Highway Administration is nearing completion of a five year, 1.5 million dollar effort titled 'Variable Amplitude Load Fatigue' to investigate the behavior of welded bridge...
Inelastic Bridge Rating Procedures for Steel-Girder Bridges
Current bridge rating procedures for steel beam and girder bridges ignore the ability of the structure to redistribute forces both longitudinally and laterally. When rating steel bridges...
Steel Alternates for the Hoover Dam Bridge
As input to the Environmental Impact Statement studies of appropriate long span bridges were performed for three alternate corridors across the Colorado River near Hoover Dam. Details...
Influence of Diaphragms on the Overall Performance of Bridges
Field data collected during vehicular loading has been used to evaluate the performance of diaphragms in composite steel plate girder bridges. This has included comparisons with finite...
Physical Testing of Two R/C Skewed Slab Bridges with Integral Wall Abutments
Two one-third scale models of an existing reinforced concrete skewed slab bridge with integral wall abutments were tested statically to failure. Typically, these bridges are designed using...
NDE of Steel Bridges by Acoustic Emission
Acoustic emission technique (AE) was used to investigate fatigue cracking phenomenon during a series of laboratory tests of various bridge steels and during field testing of an in-service...
Nondestructive Inspection of Steel Bridge Members
Assessment of the conditions of an aging population of bridges in order to determine the proper maintenance or retrofit operation is a challenge of great importance to bridge engineers...
After-Fracture Response of a Two-Girder Steel Bridge
The I-40 bridges over the Rio Grande are due to be razed in mid 1993 due to geometry and traffic safety considerations. The bridges are classified as 'fracture critical' two girder steel...
Modal Analysis Technique for Bridge Damage Detection
The dynamic responses of a wide-flange steel beam with artificially introduced cracks were studied analytically and experimentally. Frequencies, displacement mode shapes (DMS) and strain...
An Efficient Analysis of Framed-Tube Structures
An efficient model for analysis of framed-tube systems is proposed in this study. The proposed model can represent the interaction between plane frames consisting the tube system. Analysis...
Optimal Design of Building Structures Using the Predetermined Sections
A practical optimization algorithm for the member design of building structure is presented in this paper. The emphasis is particularly concentrated on the practical applicability of the...
Ductility Analysis of Overload and Settlement
The concept of sufficient ductility to avoid premature or brittle failures is gaining wide acceptance in structural engineering and is an important aspect in mitigating the consequences...
An Innovative Connection Detail for High-Rise Buildings
Composite columns consisting of hollow steel tubes filled with high strength concrete have been used in high rise building construction in the USA and Far East Asian countries. The focus...
Seismic Design of Steel Beam-to-Box Column Connections
This paper is a study of the ductility requirements of steel beam-to-box column connections using the bolted beam web and welded beam flange details. Since the beam moment at the connection...
Recent Successes in Welding Jumbo Shapes
A rather unique structure utilizing jumbo shapes was recently designed and fabricated. The structure was 100% welded according to the specifications for welding jumbo shapes recently developed...
Design of Monosymmetric Sections in Flexure
Monosymmetric members are generally I-shaped, symmetrical about the plane of the web, and characteristically have a larger compression flange than tension flange. Examples are crane girders...
Return to search