Laplace Valve Stroking to Control Water Hammer
The method of Laplace valve stroking to control water hammer is presented. Attention is directed to the most frequently encountered of the simple systems: a single pipe originating at...
Shape Effect on Bed-Load Transport in Pipes
The nature of part-full flows in pipe sewers produces different channel shapes resulting in non-uniform shear stress distribution on the wetted perimeter. New experimental data were utilized...
Regulation of Flow Downstream of Weirs
Reregulation weirs are one means adopted by the Tennessee Valley Authority (TVA) to provide continuous improved minimum flow and wetted area for aquatic life downstream if hydroprojects...
Storm Drainage Channel Rehabilitation
30 km (19 miles) of existing concrete lines storm drainage channels were studied due to repeated failures. Alternate failures causes were hypothesized and evaluated. Physical testing was...
Threats to Bridge Stability from Scour Related Failures of Drop Structures
Catastrophic failure of bridge foundations may occur when channel bed elevations are lowered unexpectedly. Bridges to be constructed in channels that are known to have bed degradation...
Friction Loss Equations for Hydropower Facilities
Many water suppliers are pursuing economic benefits from water supply and distribution systems through development of hydropower facilities on pipelines. Excessive pressure head that used...
Model Study of Center Hill Fuse Plug Spillway
Model tests of a fuseplug spillway mounted on the fixed crest of an embankment dam were conducted to develop a satisfactory design that would fail in a orderly fashion at a prescribed...
Debris Flow Initiation and Termination in a Gully
A comprehensive simulation model predicting the debris-flow discharge hydrograph, solids concentration in it and the process of variation of the channel due to vertical as well as lateral...
Methods for Prediction of Maximum Scour at Coastal Structures
The most common coast scour-related problems are toe scour at rubble mound structures and vertical seawalls, and scour at the base of piles and horizontal pipelines. Existing scour prediction...
Progressive Failure of an Overtopped Embankment
The failure of an overtopped embankment is a problem of a very complicated nature. Concerned organizations are interested in information that can be used in future planning and development...
Local Scour at Bridge Piers in Alberta?Case History
A two span steel truss bridge with a rectangular concrete central pier was built over the Oldman River near Brocket in south-west Alberta in 1954. Initially the bridge was built square...
Probability of Bridge Failure Due to Scouring
Models to estimate depth of scour at bridge piers and abutments are available in many forms,but all of them are based on constant discharges. Their results vary widely and engineering...
The Connecting Method of Steel and Concrete Using Long Deformed Bar Studs
A new welding technique for long horizontal studs of 19 mm and 22 mm diameters was established. The transmission of shearing and bending forces was evaluated using large model tests. Actual...
Design of Composite Slabs for Vertical Shear
Three major modes of failure should be considered in the design of the positive moment regions of composite slabs incorporating profiled steel sheeting, viz.: flexure, longitudinal slip...
Proposal on Story Drift Limit Based on Axial Behavior of Column under Seismic Loads
The main function of columns primarily is to support axial loads both under and after repeated lateral loading from earthquakes. A definition of the story drift limit in any structural...
Behavior of Concrete-Filled Steel Tubular Three-Dimensional Subassemblages
Three-dimensional subassemblages consisting of a concrete-filled steel tubular column and four H-shaped beams were tested under a constant axial load on the column, constant beam loads...
The Behaviour of Reinforced Concrete Beams Manufactured with Side Profile Sheets
The paper describes in qualitative terms the fundamental principles that control the behaviour of a completely new form of construction in which reinforced concrete beams are constructed...
Microtunneling: Overview and Case Study
Microtunneling is defined in the United States as a remotely controlled, laser guided pipe jacking process, which does not require personnel entry. This paper describes the components...
The Pipe/Soil Stiffness Ratio Variable
This paper reviews the factors which affect the reactions and defines performance limitations of buried flexible plastic pipe as a function of load-induced strains and deflections. The...
Ovality in Pipe Rehabilitation Design
Pipes in need of structural rehabilitation often have longitudinal cracks (at the crown and elsewhere) and exhibit significant ovality (5-10%). When these pipes are lined with current...
Return to search