ASCE will be sunsetting the Civil Engineering Database (CEDB) in the coming months. We encourage you to start using the ASCE Library to perform content searches. In the ASCE Library, you can save your search results as well as receive email content alerts when new content relevant to your area of interest is published. Try it out today at https://ascelibrary.org.

 

Pressuremeter Correlations for Preconsolidated Clay
Conventional triaxial compression and consolidation tests are often utilized to obtain parameters for design of foundations. More recently, Menard pressuremeter test results have been...

Ground Improvement Evaluation by In-Situ Tests
The application of in-situ testing to the design and evaluation of a large sand densification project for the Jebba Hydroelectric Development is described. Correlation between the standard...

Reliability of Pile Capacity Assessment by CPT in Overconsolidated Clay
Correlations for unit skin friction and end bearing are established between cone penetration test (CPT) records, triaxial data and a small data base of measured skin friction and end bearing...

Permeability, and the Field Pumping Test
Methods of estimating in situ permeability of soils are discussed including laboratory tests, borehole tests and field pumping tests, with emphasis on the latter. Techniques for designing...

Use of SPT and CPT Tests for Evaluating the Liquefaction Resistance of Sands
A cone penetration test (CPT)-liquefaction resistance relationship has been established using the large body of standard penetration test (SPT) data. Factors for relating CPT tip resistance...

In Situ Testing for Ground Modification Techniques
Presented are the status of three in situ testing techniques in relation to Ground Modification and a general overview of eight Ground Modification methods with case histories and appropriate...

Electrical In Situ Measurements for Predicting Behavior of Soils
A new method is presented for predicting the in situ stress-strain behavior of fine grained soils based upon in situ measurements of its electrical properties. The method involves the...

Comparison of the SPT,CPT, SV and Electrical Methods of Evaluating Earthquake Induced Liquefaction Susceptibility in Ying Kou City During the Haicheng Earthquake
The capability of SPT, CPT, Shear Wave Velocity and Electrical methods to evaluate earthquake induced liquefaction susceptibility of soil deposits consisting of sensitive clayey silts...

Predictions of Pile Shaft Capacity With the PLS Cell
In situ measurements of stresses and pore pressures on a model pile shaft, the Piezo-Lateral Stress (PLS) cell, are utilized to reconstruct the conditions of load tests involving two large...

Flat Dilatometer Tests in Calibration Chambers
This paper presents the results of a series of Flat Marchetti's Dilatometer Tests (DMT's) performed in a large Calibration Chamber (CC) on dry Ticino (TS) and...

Residual Soil Settlement From Pressuremeter Moduli
The Menard pressuremeter test is briefly described, and practical drilling techniques are summarized for Piedmont residual soils. Applications and limitations of the pressuremeter are...

Landslide Investigations Using the Weight Penetrometer
The weight penetrometer is a light weight device and can be easily deployed on slopes not accessible to conventional exploratory tools such as drill rigs or cone penetrometers. The weight...

A Modern Cone Penetration Testing Vehicle
The geotechnical group at the University of Florida recently purchased a new insitu testing cone truck. This is a powerful, all wheel drive, off-the-road vehicle designed specially for...

ECPT Investigation of a Slurry Trench Cutoff Wall
ECPT (electronic cone penetration testing) was used to investigate a soil-bentonite backfilled slurry trench cutoff wall at Calamus Dam in Nebraska, The wall was tested shortly after its...

Landslide Investigation Utilizing Electric Cone Penetration Testing
A geotechnical investigation was conducted of landsliding at a hillside residential property to evaluate both the extent of the landslide and the stability of the fill materials as well...

Waterfront Electric Cone Penetration Testing
Offshore deployment methods developed for use by the oil industry were combined with less expensive nearshore drill barge technology. This resulted in the successful completion of cone...

Dilatometer Tests for the Design of Grouted Piles in Rock
A case study of drilled and grouted piles in rock, which were analyzed using results of down-hole dilatometer tests is presented. The tests were performed from a jack-up platform in water...

In Situ Tests Aid Design of a Cylinder Pile Wall
In situ testing was used to verify geotechnical design parameters and modify construction for a 22 million dollar slope stabilization project near a major highway interchange. The project...

Pressuremeter Tests and Shoring Wall Design
Pressuremeter testing was used as an integral part in the design of the temporary tieback shoring wall for the Columbia Center office building in Seattle, Washington. Pressuremeter testing...

Probabilistic Study of SPT Liquefaction Analysis
The influence of earthquake magnitude upon the commonly used correlation between Standard Penetration Test (SPT) blow count and liquefaction potential is evaluated using a probabilistic...

 

 

 

 

Return to search