Serviceability and Durability of Construction Materials
The proceedings of the Materials Engineering Congress held in Denver, Colorado from August 13-15, 1990 include papers from 37 sessions that address the theme Serviceability and Durability...
Building Blocks for the Future
In the near term, advanced, conventional materials�namely higher-strength steel and concrete�will dominate infrastructure rehab. New steels of higher strengths and toughness are increasingly...
Oil Spills
Management and Legislative Implications
American Experiments with Laminated and Multiple-Membered Arches
This chapter explores the history of laminated and multiple-membered arches in America....
Geosynthetic Shields For Dams
A series of large dams in Europe, waterproofed by geosynthetics, may become U.S. prototypes. In Europe, the faces of more than 30 large dams now contain geotextiles and geomembranes. In...
Building Moon Bases
It is widely accepted that the U.S. will begin to build a base on the moon at the turn of the century, and much of the design work has already been done. Based on papers presented at Space...
Building in Reservoirs
The Croton Supply System, one of the three major water supply systems for New York City, is undergoing extensive rehabilitation. In an innovative use of space, some of the new construction...
Some General Remarks on the Structural Behavior and Load-Extension Characteristics of Coated Fabrics with Special Reference to PTFE-Coated Glass-Fiber Fabric
The understanding of fabric behavior, and of coated fabrics in particular, is essential for the design and analysis of fabric structures. Although many research papers have been published...
Transmission Line Insulator Assembly Reliability
Transmission line insulator assemblies made up of ceramic or composite insulators and associated hardware are used to mechanically support and electrically isolate energized conductors...
Effect of Imperfections on Structural Performance
This paper briefly describes the effect of initial crookedness and residual stress on the behavior of steel members. Both imperfections are unavoidable consequences of modern fabrication...
Repair and Rehabilitation of Damaged Steel Flexural Members
In earlier years, the primary method for repairing steel flexural members was to replace the member. However, with the cost of labor and material increasing dramatically over the last...
Local Buckling Behavior of Plate Elements
In the elastic post-local buckling range, the stress distribution across the width of compression elements of light gauge steel shapes is nonlinear. For code implementations, these stress...
Double Angle Bracing Members
It has been pointed out that when a single line of bracing is used, the member is usually made from structural tubing. It has been suggested that when the loads are not too great, consideration...
Simple Methods for Design of Steel Gusset Plates
This paper presents two simple methods for design of steel gusset plates. In the first method, the wedge theories are applied to establish state of stress in steel gusset plates. In the...
Strength of Biaxially Crooked Jumbo Columns
The ultimate strength of axially loaded jumbo columns with biaxial initial out-of-straightnesses is analyzed by the finite element method. The analysis makes use of the measured residual...
Notable Unbuilt Bridges
In the examples of unbuilt bridges discussed, many different ideas and concepts have been proposed. Most appear to be basically sound in nature, although rather innovative and daring....
Analysis of the Non-Planar Response of a Cantilever, with the Aid of Computerized Symbolic Manipulation
The nonlinear differential equations governing the static deformations of a cantilever with a tip mass are formulated and analyzed with the aid of computerized symbolic manipulation. The...
Total Optimization of Truss Considering Shape, Material and Sizing Variables
A total optimum design method is developed for truss structures in which the shape of the structure, discrete material kinds and cross-sectional areas of member elements are optimized...
Plates and Shells with Crack-Like Flaws
The formulation of new hierarchial finite elements for the analysis of laminated plates and shells in the presence of flaws are discussed. The performance of the elements is evaluated...
Polypropylene FRC In Steel Deck Composite Slabs
Engineers, testing laboratories, universities and metal deck manufacturers have studied polypropylene fiber reinforced concrete (FRC) and compared the results with similar slabs reinforced...
Return to search