A Mechanistic Approach to Pavement Design for Nome Airport
The analysis of performance and design of the pavement structure for the North-South runway at Nome Airport is based on the mechanistic approach. In the mechanistic approach, calculated...
Use of Rigid Insulation Below Grade for Roadways and Parking Areas
Minnesota Power's Herbert Service Center is located 3 miles north of downtown Duluth, Minnesota. The facility, constructed in 1967, consists of primary buildings, cold storage...
Future Technology for Disbonding Snow and Ice from Pavements
Current techniques to remove ice and compacted snow from pavement surfaces are costly because they needlessly crush or melt most of the ice layer. Also, in many cases they do not accomplish...
Minnesota Road Research Project - An Overview
The Minnesota Department of Transportation in cooperation with the Federal Highway Administration and the Local Roads Research Board of Minnesota is constructing the Minnesota Road Research...
Tomorrow's Toll Road
Techniques using automatic vehicle identification (AVI) currently provide the most efficient form of electronic toll collection. Several systems have been installed in the U.S. in the...
Houston Moves Forward Again
The National Transportation Plan, as released by Transportation Secretary Samuel Skinner, advocates the construction of toll roads and calls on local governments to devise and finance...
Design of Large Capacity Coal Silos for Service Life
Design and construction of Large Capacity Coal Silos for service life requires a careful consideration of the silo configuration as well as the material handling system. This paper presents...
Improved Corrosion Protection for Flue Gas Systems Utilizing a Dual Liner Concept
A unique system of corrosion resistant materials has shown excellent performance and durability in flue gas systems for fossil plants, cogeneration plants, waste incinerators and waste-to-energy...
Procedure for Seismic Evaluation and Design of Small Bore Piping
Simplified methods for the seismic design for small bore piping in nuclear power plants have been used for many years. Various pipe designers have developed unique methods to treat the...
Anchoring?A New Generation
During the time period of NRC Bulletin 79-02, and certainly afterwards, the use and application of wedge type anchors in Nuclear Power Plants took on a new perspective. The data gathered...
Introduction to Structural and Mechanical Failure Modes for Nuclear Power Facilities
The three papers presented in this section discuss the types of information (i.e., dynamic tests, earthquake experience and analytical data) which are used in predicting the capacity of...
Containment Capacity and Failure Modes Beyond Design Basis Conditions
Analytical and experimental studies have shown that containments can at least sustain two to three times design pressures. Under the severe accident overpressure loading, experimental...
Brule Project Spillway Rehabilitation and Expansion
Brule Hydroelectric Project is located near Florence, Wisconsin, on the Brule River about 1.5 miles upstream of its confluence with the Michigamme River. The 80 year old dam developes...
Low-Rise Shear Wall Failure Modes
A summary of the data that are available concerning the structural response of low-rise shear walls is presented. These data will be used to address two failure modes associated with shear...
Failure Modes of Flat Bottom Vertical Storage Tanks
Flat bottom vertical storage tanks are important components in essential nuclear power plant safety systems. Data on the seismic capacity and failure modes of such tanks have been identified,...
A Computerized Completion
The original designers of the 1.6 million sq ft Fillmore Center in San Francisco (its largest mixed-use development project in 20 years) had specified a large amount of steel reinforcement...
Jailhouse Design
According to statistics from national corrections groups, the inmate population in the U.S. has reached 1 million and could double by 1995. With the constant need for more beds, engineers...
Structural Approximations in Multi-Story Buildings
Simplified computer analyses and various approximate hand calculation methods are extremely valuable in structural engineering for multi-story buildings both during the preliminary design...
Wind Frame Design for Mid Rise Buildings
A brief discussion of drift limits is followed by design procedures for unbraced moment resisting wind frames and initial selection of optimized member sizes for chevron bracing frames....
Simplified Second-Order Inelastic Analysis for Steel Frame Design
Several current approaches are outlined that account for the spreading of plasticity in a second-order inelastic analysis of frames. The approaches are based on modifications to the simple...
Return to search