Metal and Plastic Pipelines: Design and Construction Aspects
This paper discusses design and construction aspects of four cross-country pipelines that were built in central Alberta, Canada during 1982-1983. The first two pipelines, carrying different...
Clay Pipe Installation?Advances in Load Factors
This report presents an evaluation of traditional load factor values for clay pipe and the development of a new bedding system which gives a higher load factor. Tests demonstrate that...
The Evolution of Jointing Vitrified Clay Pipe
Advances made in the jointing of vitrified clay pipe during the last half century, illustrate the concern of the clay pipe industry to provide top quality jointing methods. Early 19th...
Sewer Construction Inspection and Testing
Sewer construction testing is the final portion of the team effort that started with the goal of meeting the requirement for a sewer system for the protection of health and environment....
Investigations into the Structural Performance of Clay Pipes
Over the past 8 years, the Clay Pipe Development Association (CPDA) has commissioned non-destructive physical testing of vitrified clay pipelines. The diameters of the pipes have varied...
Unique Installation Methods for Large Interceptor in Poor Soil Conditions
The construction of approximately 1. 5 miles of a major sewer interceptor in downtown Boston encountered some unique construction challenges. The entire route required dewatering during...
Failure of a Large Reinforced Concrete Pipeline
This paper describes the damage that occurred when a landslide overloaded an 11 ft diameter reinforced concrete pipeline. The 8 ft lengths of pipe, each of 11. 5-in. wall thickness, were...
SPIDA: An Analysis and Design System for Buried Concrete Pipe
The paper presents a description of a new computerized direct design method for buried concrete pipe named SPIDA (Soil-Pipe Interaction Design and Analysis). Also the technical basis and...
Experiences in Concrete Pipeline Construction in Ontario 158-1985
The paper discusses the title subject in terms of concrete pipe fabrication methods and plants, pipe jointing and jointing materials, and construction experiences in the Province of Ontario,...
Simplified Stress and Deformation Analysis for Pipeline Construction
This paper discusses the strength and deformation behavior of flexible steel pipes during pipeline construction. Some possible simple and quick solutions to these special design and construction...
Longitudinal Prestressed Piping for District Heating
The design of recently installed hot water district heating systems in the United States is based on similar systems developed in Europe. Longitudinal prestressing is used in the design...
Modeling Failure Probability of Underground Pipes
Factors influencing the performance of underground gas pipes are identified through a literature search and contacts with several utility companies. These factors are categorized as (i),...
Stress-Intensification Factor and Flexibility Factor in Seismic Analysis of Continuous Buried Pipelines
The topics of intensified stresses and increased flexibility in pipe bends subjected to bending loads are discussed in this paper. Also discussed are dynamic strain compatibility between...
A Practical Approach to Selection of Waterline Materials for Use in Expansive Soils
The authors previously investigated the performance of asbestos-cement, polyvinyl chloride and ductile iron pipe in the expansive soil environment. Expansive soil forces on the pipe were...
Bending Moment of Underground Flexible Pipes in a Centrifuge
The effect of several factors on bending moment of an underground flexible pipe section buried in a ditch with sheet piling was investigated experimentally by means of centrifugal model...
Field Burial Tests of Corrugated Double Wall PVC Pipe
A new lightweight PVC pipe, consisting of a smooth inner wall and a corrugated outer wall, has been introduced in the U. S. sanitary sewer market in 4 through 10 in. diameters. Field burial...
Stiffness Requirements for HDPE, Profile Wall Pipe
For the past two years the Gulf Oil Corporation has sponsored a research study on profile wall High Density Polyethylene (HDPE) pipe at Texas A & M University. A pipe design computer...
Investigation of the Long-Term Creep Modulus for Buried Polyethylene Pipes Subjected to Constant Deflection
The tests reported in this paper are simulating the stress relaxation in constantly deflected pipe rings of various high density and medium density polyethylene grades. The pipe rings...
Long Term Deflection of Buried Plastic Sewer Pipes
During the 70's and the early 80's a research program has been carried out in Sweden regarding the long term behaviour of buried plastic pipes. The program has...
The Relative Strain as a Design Criterion for Buried uPVC Gravity Sewer Pipes
When designing buried plastic sewer pipes, the relative strain caused by deflection of the circular pipe section is of particular interest. The reason for increased interest is the present...
Return to search