Compressive Strength of Large Scale HSLA-80 Steel Cellular Sections of a Double Hull Ship Structure
An analytical and experimental large scale test program was conducted to investigate the instability failure modes of cellular double hull box sections. The main emphasis of the study...
Review of Cold-Formed Steel Purlin Design
The use of cold-formed steel members as roof purlins for single story industrial and commercial buildings is commonly recognized. These members typically have either a C- or Z-shaped cross...
Column and Beam-Column Design - A World View
This paper is concerned with the design of columns and beam-columns in steel building frames. Design provisions found in some selected codes viz. AS DR87164 87(Australia), BS5950 Part...
Some Aspects of Compression Member Design in Australia
The paper summarizes and elucidates the provisions of the Australian Standard AS4100-1990, Steel Structures, for the design of compression members. Emphasis is placed on those aspects...
Phoenix Central Library: Reading Room Roof
This paper discusses the design and analysis of the cable truss roof over the fifth floor reading room of the new Phoenix Central Library. Forty pairs of diagonally oriented cable trusses...
What Controls the Ultimate Load of a Glulam Dome?
A glulam dome is analyzed with the finite element method to determine the governing failure mode and ultimate snow loads. The dome consists of a triangulated network of curved glulam beams,...
Field Measurements of Tensile Forces on a Spherical Dome Sector Caused by Internal Load of a Granular Product in Storage
Using a number of existing equations developed application to silos, bins, and hoppers, the horizontal load resulting from the stored product can be calculated. In this paper, the physical...
AWS versus AIJ Tubular K-Connection Design Rules
Among various existing design rules for circular tubular connections, the AWS rules are compared with the AIJ rules because of differences between the two. Subjects of discussion include...
The Behaviour and Design of Stressed-Arch (Strarch) Frames
The paper presents an overview of the stressed-arch structural system and the associated research program undertaken at the University of Sydney between 1988 and 1992. The objectives of...
Research and Application of Various Joints of Space Grid Structures in China
This paper introduces the research work results and applications of various joints of space grid structures in China. It also gives out formulas for determining the loading capacity and...
Structural Tests on the Suspen-Dome System
The 'suspen-dome' system, which the authors have developed, consists of a single-layer truss dome and a cable structure. The present paper deals with the results of structural tests conducted...
Simulation Procedure for Buckling Behaviors of a Reticular Dome
Complex behaviors of the ball-joint connection, especially used in steel space structures, are expressed in the numerical model to confirm the estimative ability of such a model by comparing...
Buckling of Single Layer Latticed Dome under Uniform Gravity Load
This paper reports on experiment and numerical analysis relating the buckling of a single layer latticed dome under uniformly distributed nodal gravity load at the dome central portion....
The Georgia Dome and Beyond: Achieving Lightweight - Longspan Structures
In the last two decades, the development of longspan roof structures has undergone a quantum leap. The introduction of steel structures, fabric structures, Bucky Fuller's tensegrity structure,...
A Practical Design and Construction of Tension Rod Supported Glazing
In designing a glass skin-covered space, for the atrium, entrance hall or other core part of a building complex, the high openness and quality requirements of the space often lead to the...
Nonlinear Behavior of Northlight Reinforced Concrete Shells
The behavior of northlight shells is very sensitive to the boundary conditions at the top and bottom edges of the shell. The aim of this paper is to investigate the structural action of...
Performance and Analysis of Frames With URM Infills
The interaction of unreinforced hollow concrete block masonry (URM) infill walls and gravity load designed (GLD) frames has been studied at Cornell University. The primary goal of this...
Behaviour of Concrete Masonry Infill - Steel Frame Structures
Twenty-eight masonry shear panels infilled in steel frames were tested to ultimate strength under in-plane, horizontal loading applied at roof level. The parameters investigated in this...
Experimental Evaluation and Finite Element Analysis of Masonry-Infilled R/C Frames
Eleven tests were conducted on 1/2-scale, single-story infilled frame specimens to study the influence of the relative strengths of the infill panels and the bounding frames and the frame...
How to Optimize Light-Gage, Cold-Formed Steel Beams
The Illustrative Examples section of the AISI Cold-Formed Steel Design Manual (AISI 1989) demonstrates how to analyze a number of different cold-formed steel sections. This paper applies...
Return to search