Learning From Pile Driving Failures: Out of Sight Can't be Out of Mind
The design of driven pile foundations for static service and strength limit state loading conditions is meaningless if the piles cannot be driven to the required depth and nominal resistance without sustaining...

Tsunami Loads and Effects
Guide to the Tsunami Design Provisions of ASCE 7-16
The devastating tsunamis that struck Chile and Japan in 2010 and 2011 underscored the critical need for new structural design criteria to improve building resilience and safeguard human life. They also...

Micropiles Support the "Missing Link": Understanding Load Transfer in Challenging Subgrades
Authorized by Congress in 1944, the Foothills National Parkway partly traverses the foothills of the Great Smoky Mountains in Eastern Tennessee. Large sections of the parkway cross high ridges located...

Geotechnical Aspects Of Coastal Impacts During Hurricanes Harvey And Irma: Logistical and Technical Challenges During Reconnaissance
As designers and managers for society’s infrastructure, civil engineers, including the geotechnical community, must understand and predict the most severe expected loadings from physical or environmental...

A Combo Foundation Does the Job: Piled-Raft Foundation Design for a Supertall Skyscraper
Lotte World Tower is a 123-story, 555-m supertall skyscraper with a 6-level basement for retail and car parking located at Jamsil-dong in Seoul, South Korea. (Editor’s Note: For additional information,...

Load Path

Urban Areas Show Progress in Reducing Nutrient Loads to U.S. Coastal Waters, Study Says

Spin, Spin, Spin
A scalable, vertical axis windmill tower with dynamic shutters that decrease wind loading on the structure has won an energy efficiency design contest....

As I See It: Rethinking the One-Third Increase in Bearing Capacity for Seismic and Wind

Calibration of Jackup Leg Foundation Model Using Full-Scale Structural Measurements
The fitness of jack-up rigs to operate in varying water depths and weather conditions is determined by "site-specific" structural assessments. These assessments are conducted by a wide range of companies...

Cracking the Nuclear Code: Finding an Alternative to the Nuclear Density Gauge
Two of the most basic quality control tests made in the field during soil construction are the soil’s moisture content and density. The establishment of a uniform procedure to compare the performance of...

A Faculty Internship: Reconnecting with the Profession
After spending eight years as a full-time academic administrator at Lafayette College in Easton, PA – one of only a handful of institutions where discipline-specific engineering programs are embedded in...

Optimized Drilled Shaft Design through Post-Grouting: Shorten That Shaft for Better Performance
Tip post-grouting is a technique used to inject, under pressure, a neat cement grout beneath the base of a drilled shaft. This method enhances or improves axial load-displacement performance by increasing...

Geotechnical Aspects of Pavements: There's More to Roads than Asphalt and Concrete!
When you jump on the highway to make that commute to work, do you think much about what's under the surface you ride on? Pavements are layered systems designed to provide a strong structure to support...

Pervious Concrete
Pervious concrete consists of a hydraulic cementitious binding system combined with an open-graded aggregate to produce a rigid pavement with typically 15% to 25% interconnected void space....

General
Design of Latticed Steel Transmission Structures specifies requirements for the design, fabrication, and testing of members and connections for electrical transmission structures. These...

Loading, Geometry, and Analysis
This Standard applies to latticed steel transmission structures. These structures shall be either self-supporting or guyed. They consist of hot-rolled or cold-formed prismatic members...

Design of Connections
Bolted connections for transmission structures are normally designed as bearing type connections. It is assumed that bolts connecting one member to another carry the load in the connection...

Pipe Characteristics
Microtunneling pipe should meet the following general requirements: Circular shape with a flush outside surface (including at the joints); Strength sufficient to withstand both the installation...

Pipe Design
The pipes and joints, once installed, must be capable of safely withstanding, for the project design life, all in-use service loads, including those associated with the following factors:...

 

 

 

 

Return to search