Field Investigations for Seismic Effects on Mechanical and Geohydrologic Response of Underground Structures in Jointed Rock
An exploratory Seismic Rock Mechanics research program has been initiated by the U.S. Nuclear Regulatory Commission at the Center for Nuclear Waste Regulatory Analyses (CNWRA) to study...
Regulatory Requirements and Long-Term Repository Host Rock Performance
The regulatory requirements governing the disposal of high-level radioactive wastes in mined geologic repositories acknowledge the long-lived nature of the wastes and require the consideration...
Potential Uses of Lead in Nuclear Waste Disposal
In order for lead to be considered as a nuclear waste packaging material, it must be shown that it has adequate corrosion resistance, and that it does not degrade the properties of other...
Testing of Materials and Scale Models for Impact Limiters
Aluminum Honeycomb and Polyurethane foam specimens were tested to obtain experimental data on the material's behavior under different loading conditions. This paper reports...
GA-4/GA-9 Honeycomb Impact Limiter Tests and Analytical Model
General Atomics (GA) has a test program underway to obtain data on the behavior of a honeycomb impact limiter. The program includes testing of small samples to obtain basic information,...
Modelling of Excavation, Thermal Loading and Bentonite Swelling Pressure for a Waste Repository
For the performance assessment of a future nuclear waste repository, the excavation of the tunnel and deposition hole, thermal loading from waste heat release and the swelling pressure...
The Radiological Capacity of Transport Casks Loaded in a 2-Region Non-Uniform Pattern
The radiological capacity of spent fuel storage and transport casks can be increased by the use of non-uniform cask loading. There are many possible combinations of spent fuel burnup and...
Computer-Aided Structural Analysis
Finite Element Methods and other numerical techniques are often taught nowadays in the undergraduate Structural Analysis courses. Commercial, structural computer programs are becoming...
Accurate Response Analysis of Seismic Distributed Mass Systems
A dynamic analysis technique of distributed mass structures is presented with a combination of the dynamic load factor approach and the dynamic stiffness matrix method. The dynamic stiffness...
An Electronic Specification for the Earthquake Resistance Design of the Highway Bridges in Pennsylvania
An interactive C program for the seismic design of highway bridges in the state of Pennsylvania is described in this paper. The program was developed in C language on a personal computer....
COMBAT.PC; a New Windows-Based Tool for Three-Dimensional Dynamic Analysis of Multi-storied Building Structures
By some accounts, analytical capability without the power of visualization is little productive; visualization is the tool that will turn computational power into practical results. COMBAT.PC...
Computer Implementation of Seismic Building Codes
The objective of this work is to implement the provisions of building codes current in the U.S. as well as those of other countries for the seismic resistant design of buildings. The work...
Buckling Optimization of Laminate Stacking Sequence with Strain Constraints
An integer programming formulation for the design of symmetric and balanced composite laminates subject to buckling and strain constraints is presented. The design variables that define...
Simultaneous Design and Location of Actuators
A chance constrained model for determining optimal dynamic control parameters for structures subjected to probabilistic forcing amplitudes is presented. Optimal feedback control parameters...
Structural Optimization to Limit Natural Periods
It is necessary to limit the natural periods of some structures to control their response to dynamic loads. Floor systems with natural periods greater than approximately 0.15 seconds may...
Stiffness Optimization Methods for Lateral Systems of Buildings: A Theoretical Basis
The sizing of the members of the lateral resistance system for multi-story buildings is often controlled by stiffness requirements. In order to achieve economical buildings, it is important...
Parallel Preconditioned Conjugate Gradient Methods for Structural Analysis Problems with Multiple Loadings
This paper describes the use of conjugate gradient method for finite element problems with multiple loading cases. Specifically, we introduce a modified conjugate gradient method for the...
Wave Motion in Aerated Rubble Mounds
Experimental investigations were undertaken to study the effect of air entrainment on wave motion in rubble mounds. The study is aimed at the understanding of the processes associated...
Source Identification and Ranking of Wet Weather Discharges in an Urban Area
A study has recently been completed to characterize the pollutant loadings to the Providence River, RI during wet weather conditions. A total of 11 land based sampling stations including...
Parallel Real-Time Dynamic Simulation of Robots
To achieve real-time dynamic simulation of a robot manipulator on a vector/parallel machine, two types of parallelism are investigated. Techniques to enhance the vectorization of the dynamics...
Return to search