Large Diameter Plastic Pipe Design
This paper presents a rationale for the design of large diameter plastic pipes for gravity flow applications. This procedure, applicable for all plastic pipes, adapts state-of-the-art...
Successful Use of Centrifugally Cast Glassfiber Reinforced Plastic (GRP) Pressure Pipes for Public Works in Sweden
Centrifugally cast GRP pipes were introduced in Sweden 17 years ago for industrial applications mainly as a gravity pipe. The process of pipe manufacturing as well as the pipe itself and...
Design of Non-Pressure Very Flexible Plastic Pipe
There is considerable debate about the correct structural design procedure to be used for very flexible plastic pipe (VFP) - typically glass-fiber reinforced pipe (GRP), reinforced plastic...
Proportioning Reinforcement for Buried Concrete Pipe
The proportioning of reinforcement between inner and outer cages that is specified in ASTM Standard Specification C76 for concrete pipe in sewer and culvert applications is examined in...
Influence of Frost Action on the Load Exerted on Buried Pipe
When work was started on revising the Swedish code for concrete pipes at the end of the 70's, a research project was carried out to evaluate the risk of increased load due...
Computational Model for Computing Dune Erosion
This paper summarizes the development of a computer model for determining potential beach and dune erosion along the Florida Panhandle. The results have been used as a guide in delineating...
Reliability Evaluation of Water Distribution System Components
Reliability engineering concepts are substantially developed and have been routinely and successfully applied to the evaluation of electrical and mechanical components. However, these...
Effect of Tall Vegetation on Erosion and Sedimentation: A Microcomputer Package
A model was developed to predict the effect of standing vegetation on sediment yield. The model is based on the relationship between local scour around standing vegetation and the role...
Lake Water Level and Sediment Management?Case Studies in Illinois
Estimation of the sedimentation in the lake is based on the soil erosion rates in the watershed, the sediment transport in the stream system, and lake trap efficiency. Erosion rates are...
Assessment of Sediment Problems in Peoria Lake, Illinois
Peoria Lake, located on the Illinois River in Illinois, is the deepest lake in the river valley. Since 1903, the lake has experienced approximately a 31% loss of original storage capacity...
Pressurization and Depressurization in Pipe Flows
When a closed conduit drainage system is subjected to variable inflow rates, the change in flow regimes between free surface flow and pressurized flow may take place. A rising hydrograph...
Microcomputers in Hydraulics-Hydrology Education
Microcomputer software is utilized for pipe network analysis, unsteady flow in pipelines, watershed modeling, flood studies, reservoir operations, dam break analysis, and groundwater systems...
Embankment Overtopping Tests to Evaluate Damage
The paper reports on studies of embankments 6 ft high, 10 to 22 ft in crest width, and 3 ft in length, with slope varying from 2:1 to 4:1. Embankment surfaces include pavement, grass,...
Overtopping of Small Dams?An Alternative for Dam Safety
A research effort was initiated in 1983 by the Bureau of Reclamation to gain insight in the development of cost-effective modifications to small embankment dams which would enable them...
A Microcomputer Program for River Sedimentation
Erosion and deposition of sediment in rivers causes numerous problems. In order to describe this process, both the hydraulic properties of the river and the mechanics of sediment transport...
Centrifugal Abrasion-Resistant Pumps in Intermediate Length Pipeline Systems
The success of long-distance slurry pipelines is in many cases dependent on careful preparation of the solids prior to transport. Positive displacement pumps are employed. However, for...
Transients in Empty Pipes Subject to Rapid Filling
A mathematical model was developed to simulate the pipe filling process and the pipe forces based on incompressible water column theory. The method easily accomodates appropriate boundary...
Analysis of Resonance in Pressurized Piping Systems Via a Microcomputer
In this paper a digital simulation technique for the analysis of resonance is presented that is appropriate for microcomputer applications. The model utilizes the transfer matrix method...
Quick Stroking: A Fast and Accurate Algorithm for Time-Optimal Valve Closure Synthesis
In this paper, a fast, simple, yet effective technique for valve motion synthesis is developed. This technique called Quick Stroking is applied to a practical example problem, and it may...
Girth Weld Defect Tolerance Criteria
This paper describes the following criteria proposed for setting allowable defect sizes in girth welds: PD 6493:1980, 'Guidance on Some Methods for the Derivation of Acceptance...
Return to search