Rate-Dependent Plasticity Representation for Energy-Absorbing Materials
A three dimensional rate-dependent plasticity constitutive model is developed for rigid polyurethane foams. In the model, the material is decomposed into skeleton and solid matrix from...
Constitutive Modeling and Simulation of Energy Absorbing Polyurethane Foam Under Impact Loading
The compressive-stress strain response of polyurethane foam under uniaxial compressive impact loading has been studied. The development of a uniaxial constitutive model from strain rate...
Stress Transfer Within Granular Geomaterials
Local stresses within granular materials are random variables whose variance depends on the size of the elementary surface considered. This paper shows that this 'mechanical scale effect'...
Random Aspect of the Stress Inside Granular Media
Micromechanics of granular media arose from the necessity of a better understanding of the relationship between the global behaviour of such materials and the physical phenomena which...
Nonlinear Behaviour of Schneebeli Packings
We present some experimental proofs of the influence of the disorder of contacts on the mechanical (non-local) behaviour of packings of cylinders. In particular, this disorder is responsible...
On the Diffusional Stress Transmission
A probabilistic diffusional mechanism for the propagation of intergranular forces has been formulated as a set of three mathematical assumptions. The equilibrium equations are complemented...
Particle Analysis of Material Behavior?A Note on Continuum Assumptions
Continuum models of materials have dominated our approach to the analysis of material behavior. Recently a number of discrete particle methods have been proposed which offer a different...
On a Micromechanical Basis of Stochastic Constitutive Laws
A procedure for derivation of stochastic constitutive laws is outlined on the basis of graph-representable linear elastic microstructures. Central to the procedure is the concept of a...
Fracture Toughness of DMMC
The fracture toughness of discontinuous metal matrix composites (DMMC) is always less than the fracture toughness of the matrix, in the same heat treatment or annealed condition. If a...
Fracture Toughness Model of Fiber Reinforced Ceramics
This paper addresses the fracture resistance mechanism in fiber reinforced ceramics, and focuses attention on the specific effects associated with the nonlinear nature of the fiber pullout...
Debonding of a Inhomogeneity from a Plastic Matrix
Inclusion debonding is addressed through the formulation and solution of the planar elastic and elastic uniform plastic problems. These problems are variants of the standard transformation...
Laser Interferometric Characterization of Acoustic Emission Transducers
The characterization of the exact response of commercially available, piezoelectric and thin film, acoustic emission transducers is of fundamental importance for the nondestructive evaluation...
Characterization of Granular Material Composite Structures Using Computerized Tomography
The behavior of particulate composites such as asphaltic concrete is controlled by microstructural features including particle and binder arrangements, interparticle contacts, and changes...
Experimental Photoelastic Analysis of Tunnels Containing Cracks
Due to the presence of cracks the strength of the structure is decreased in the present paper an experimental two dimensional photoelastic technique has been developed to analyze the circular...
On the Bifurcation of Elasto-Plastic Crystals During Multiple Slip
Conditions for the localization of deformation in elasto-plastic crystals experiencing multiple slip are discussed using multisurface plasticity theory. In particular, some important characteristics...
Instability of Slopes with Nonassociated Flow
Experimental investigations of the conditions for instability have shown that granular materials may become unstable inside the failure surface. For states of stress below the failure...
Densification/Creep Behavior of Experimental Glass-Ceramic Waste Forms for Immobilization of High-Level Calcined Waste at the Idaho Chemical Processing Plant
A mixture of simulated high-level calcined waste (HLW) and Frit additives was hot isostatically pressed (HIPed) to a dense glass-ceramic waste form. A densification mapping software was...
Mechanical Response of Cellular Materials Used in Waste Shipping Containers
Material behavior of impact limiters such as aluminum honeycombs and polyurethane foams has been studied experimentally. Four densities of aluminum honeycombs were tested: 3, 8, 12, and...
Direct Tensile Test: Stability and Bifurcation
Unnotched specimens of quasibrittle materials that exhibit post-peak strain softening do not deform symmetrically in a direct tension test. The phenomenon (which is similar to the recently...
Two-Dimensional Statistical Micromechanical Models for Microcracked Brittle Solids
Recent development undertaken by the authors in two-dimensional statistical micromechanical models for brittle solids with randomly located interacting microcracks is presented. Overall...
Return to search