Steel Girt Design
Procedures are presented for the design of light gage cold formed girts and hot rolled girts. The effects of continuity, sag rods, and wall sheeting are discussed. Design procedures are...
Floor Vibrations ? Tips for Designers
The purpose of this paper is to suggest a number of practical concepts which can be used to improve the performance of floor systems subject to occupant induced motion from either walking,...
Composite Floor Vibrations: Predicted and Measured
Several steel composite floor systems of relatively long span trusses for a number of high rise structures in the Chicago area have been subjected to field measurements to evaluate their...
Buckling of Unsymmetrical Thin-Walled Members
The formulation of a three-dimensional model based on p-version finite element method for the elastic buckling analysis of unsymmetrical thin-walled members under axial compression and...
Behavior of Cold-Formed Steel-Concrete Composite Beams
An experimental investigation was conducted at California State University - Long Beach to study the structural behavior of composite beams made of thin-walled cold-formed steel stiffened...
Cold-Formed Z-Sections Under Axial Load and Bending
The use of cold-formed Z-section members as beam-columns presents some unique design problems which are not adequately addressed in the current design specifications. If these members...
Automated Load Capacity Determination of Cold-Formed Steel Compression Members
This paper presents an automated approach for the evaluation of the axial load capacity of nine cold-formed steel sections according to the latest AISI-1986 Cold-Formed Steel Specification....
Structures with Semi-Rigid Bolted Connections
Modern methods of aseismic protection encourage use of connections capable to dissipate energy with little or no deformations. The present paper is a summary of studies of semi-rigid bolted...
Seismic Response of Flexibly-Connected Steel Frames
The response of typical low-rise steel building frames designed by the 'Type 2 Construction' method to moderate earthquakes is examined. Such frames are often...
Tests on Brace and Link Connections for EBFs
This paper describes recent test results on the behavior of selected connections for seismic-resistant Eccentrically Braced Frames (EBFs). These tests provided data on the performance...
Brace Connections for Ductility
Influence of connection design on the seismic behavior of welded bracing members made of double channels is studied in this paper. Shortcomings of commonly used connection details as per...
End Plate Moment Connections for Cyclic Loads
Three pilot tests of full size end plate moment connections under cyclic loading are discussed. In one of the specimens, the premature fracture of one of the inner bolts suggests the possibility...
Strength of Biaxially Crooked Jumbo Columns
The ultimate strength of axially loaded jumbo columns with biaxial initial out-of-straightnesses is analyzed by the finite element method. The analysis makes use of the measured residual...
Evaluation of the Rotation Capacity of Wide-Flange Beams Using Shell Finite Elements
Numerical simulation can be useful for planning of experimental tests, performance of parametric studies, and achieving an understanding of complex three-dimensional behavior that may...
Behavior of Single Angles Under Compression and Biaxial Bending
Angle struts are being used extensively as web members of trusses, bracings of buildings, and they are widely used as main members in transmission and lattice towers. Because of their...
Stablity Considerations in the New E&CS Building
The new Engineering and Computer Science (E & CS) building at California State University, Sacramento (CSUS) is a five-story structure characterized by two shear walls in the east-west...
Stability Analysis of Steel Compression Members by a Modified Finite Strip Method
The method of structural stability analysis utilized in this paper is a combination of the classical bending theory and the finite strip method. Combining the assumptions of traditional...
Hysteresis Studies Including Post Buckling of Angle Web-Members for Truss-Type Girders
The paper presents analytical studies of the buckling capacities and hysteresis behavior of angle-web members of truss-type girders. The eccentricity between the loading point and the...
Tripping and Strength of Asymmetrical Plate Stiffeners
Tripping (lateral-torsional buckling) of symmetrical or asymmetrical plate stiffeners can be analyzed by using differential equations or energy formulation. An analytical study is reported...
Stability Analysis in Bracing and Support Design
A post-buckling stability analysis is carried out for struts with multiple elastic lateral supports. Both hinged-end and fixed-end conditions are considered. A criterion of sufficient...
Return to search